similar to: Unable to connect to FWD

Hi, I have two asterisk servers one is connected to the PSTN and the other one is connected to SIP users. The two servers connect with each other using IAX. When I have an incoming call from PSTN to the asterisk servers and have a forward to go back out to the PSTN the two IAX channel bridge together. Now every time I dial a DTMF digit, the asterisk is sending two DTMF digits. I enable

Hi Folks, Just wondering if anyone can give me some pointers, I'm configuring Asterisk to talk to FWD's new IAX service. The asterisk server is behind an iptables NAT Firewall, with port 5036 forwarded: $IPTABLES -t nat -A PREROUTING -p udp -d $EXTERNAL_IP --dport 5036 -j DNAT --to-destination 172.16.20.200:5036 I can make outgoing calls just fine, but when I receive an inbound call

Hallo Did you allow udp outgoing on 4569 as well.. i found udp bit different than tcp when comming to firewalls liaan ----- Original Message ----- From: "Bartosz Wegrzyn - asterisk" <junk@lexon.ws> To: <timebandit001@gmail.com>; "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Monday, February 21, 2005 12:29

Hi All, I am using Asterisk 1.4.26.2 and I am getting the following problem making connections to this server. My other servers are Version 1.2.x which have no problems and this 1.4.26.2 server can call the other 1.2.x servers. The error is: chan_iax2.c:4251 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 192.168.25.250 in the

This may not strictly be an asterisk question, but not sure where else to post ... I have an Asterisk test server setup with two firefly clients, one on the local lan and one on an external ip address. Both clients are setup the same way and voice calls work fine. The asterisk console reports a "Registered" message for the external client at about one minute intervals but the

G'Day, I have a bit of FireFly problem that hopefully someone has seen before. What happens is if I make to or receive a call from the FireFly network the call will connect successfully. However, around 10 seconds after I answer the call I am disconnected. The weird thing is same thing happens if I make a call. I've had a look at the * console and I can't see that my * PBX drops

On the asterisk1 I got this: register => username:secret@ipaddress2 [eop] username=username secret=secret type=peer host=ipaddress1 auth=md5 on the second box I got this this host is ipaddress2 [incommingiax2] username=username type=user secret=secret host=dynamic context=from-internal-custom auth=md5 on first host 1 am getting: Jun 22 14:42:10 NOTICE[2398]: chan_iax2.c:7411

Hi My head hurts... Can anyone help out here, my remote IAX can see my local IAX and visa versa, conversation starts, I can dial my remote (POTS) landline number, remote end answers, trys to route to local iax2, I see it start the conversation here, the extension (SIP) rings once and then it dies... Both ends are defined with accept IPADDRESS to keep it in the family and simple.. Debug info

I'm starting to get this to work! Well I got Voice Mail to work! All calls goes to voice mail without ringing the users phone (iaxComm). Here is my iax.conf and my extensions.conf Any help would be great!! Thanks -------------- next part -------------- A non-text attachment was scrubbed... Name: extensions.conf Type: application/octet-stream Size: 1039 bytes Desc: extensions.conf Url :

[ Sorry, I incorrectly copied some Reference headers into this post and tacked it onto the wrong thread. -Steve ] So far, I have been able to receive incoming iaxtel calls via my assigned 1-700-xxx-xxxx number, but only when using md5 authentication in iax.conf: [iaxtel] type=user ; Incoming calls only context=incoming auth=md5 secret=<mysecret> ; Required for

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default]

Hi I've 3 iax connections to my provider , each of them have own DID , PH1<----| | \/ PH2<-->|-----| <---------------------------> |----|<-- DID1 | A1 | <---------------------------> |ISP |<-- DID2 PH3<-->|-----| <---------------------------> |----|<-- DID3 I had iax phone on each of this connection , but now I want to terminate all

What settings are people using? I've seen the ones from dslreports but I'm in that lucky group of people that paid the 1 euro just to have it no longer work. Even after I setup a additional account over the weekend it still doesn't work. And, of course, etherreal only shows encrypted traffic so I can't snag any config settings from it. Any assistance? -----Original

Dear Sanjay, Sorry sanjay i miss to explain completely. My PC2PC mean is Dialer2Dialer i want to allow call between Dialer with out any registry and authentication through IAX. so i need to setup Asterisk accept calls from any user and users can call to each other without any password and registration. please help how can i configure Asterisk using IAX in this regards. thanks, Asif Message: 9

hi, I use IAX softphone with asterisk and I notice that a call between two IAX softphones end after 1 min. Then I can't hear anything but the call still in progress. I have this log in asterisk IAX debug: Rx-Frame Retry[No] -- OSeqno: 002 ISeqno: 002 Type: IAX Subclass: ACK Timestamp: 00016ms SCall: 21589 DCall: 00001 [192.168.1.22:4569] Tx-Frame Retry[000] --

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default] exten=>_.,1,Dial(IAX2/${EXTEN})

i have 2 asterisk servers one on CentOS and one on Fedora , i configured IAX trunking between the 2 servers so that i dial -say from a sip extension 2000 on fedora server to a sip extension 3000 on CentOS server the call seems to be established but hangup automatically after very short time and here is the iax2 set debug command result on centos server and also my iax.conf and extension.conf and

Hi, I'm trying to track down why I'm getting calls dropped on an infrequent basis between two asterisk servers which are at the same physical location and connected to each other with UTP ethernet. Here is the connection diagram Asterisk Server 1 ===UTPENET== Switch ====UTPENET==== Asterisk Server 2 I see sporadic RX and TX frame retries when I enable iax2 debugging on either box.

I am using Teliax to terminate my calls, and I have 3 licenses' for g729 from Digium. "show translations" verifies that the registration took place. When I place a call, having "allow=g729" as the only allow option in iax.conf, I get the following error: WARNING[361]: chan_iax2.c:6017 socket_read: Call rejected by 208.139.204.228: Unable to negotiate codec If I place a

Hello all! I?ve got a problem with the IAX setup. I?m previously only experienced with SIP, so that may be part of the problem. However, I?ve managed to register with the IAX server without any trouble (register line apparently works as it should), and I am also ale to make outbound calls. However, for inbound calls, all I get is this (from iax2 debug): Mar 29 17:44:18 NOTICE[11502]: