similar to: Uniden UIP 1868 / Asterisk experiences

I had a working system using * 1.0 and then 1.2 and now Asterisk 1.4.13 with addons 1.4.4, zaptel 1.4.6, libpri 1.4.2. I have a mix of Grandstream (GXP2000), Uniden uip-200, Linksys Wireless G, and analog phones via Adtran chan bank. When I went to * 1.4.13, the Uniden phones stopped being able to login to voicemail. All phones are on same lan with Asterisk. I get 'Login incorrect'

Hi - I'm wondering if any has experience with the Uniden UIP-200 phones. The product info says that the 8 led buttons at the top are all programmable. Can they be programmed as separate line appearances (ala Snom 200, Cisco 7960, Zultys Zip4x4, etc)? In other words - is the phone capable of multiple SIP registrations? Also, the post about these phones at voip-info.org mentions some

I have several too and I also see this problem on occasion. Like you say, it is fairly rare and I can't pinpoint a cause or tell if it is a symptom of something else. I think I wrote to tech support about it but never heard anything. I'm wondering how long they will continue to support the phone. -Nate > -----Original Message----- > From: Jerry Geis

I just purchased 30 of these after testing one for a few months and would like to quickly purchase another 40. We really like these phones: good sound quality, good echo control (no echo in speaker phone), power over ethernet support, 10/100 switch, 8 programmable keys. Unfortunately we missed on big problem with Call waiting in our testing. When using asterisk 0.9.1 or rc2 the phone will reboot

I've been looking out for the Uniden UIP1868 for a while now, but I haven't seen it anwhere that I'm used to buying things from. According to froogle, a couple of places (that I've never heard of) have a small number in stock (small = 10 in this case). I'm doubly suspicious because even uniden's own online store doesn't have them available yet, not to mention

Hi, I'm new to asterisk, and have a uniden UIP 200 that I got off of ebay. I'm having trouble getting the phone to register with asterisk. I've tried a few different settings. I'd be extremely grateful if someone with a similar setting could give me the sip.conf block for the UIP and the settings you're using in uniden.txt. Here's what I have currently: IP of phone

Anyone used any of the Uniden VoIP gear, any comments one how easy it was to integrate with asterisk? Also quality of the gear in general? This unit _looks_ pretty nice on paper http://www.uniden.com/productpop/00_productpop.cfm?prd_code=UIP1868 -- Harondel J. Sibble Sibble Computer Consulting Creating solutions for the small business and home computer user. help@pdscc.com (use pgp keyid

I just got my wife this phone, and when calls come in on the queue it will not ring, if I dial the ext it rings, here is the config from the tftp server: Thanks unidencom.txt # UIP200 Mass Configuration System Generic File # Notes: # 1. Lines start with '#' are comments # 2. To leave a field value unchanged (as saved on local phone), leave value to blank. # 3. To set a field's

I have a UIP200 on the way for eval. Does anyone have tips or tricks to get it working right away with * ? I hate having to go through the pain someone else braver than I went through already. :) Tim --

No kidding, every time. I know I have the config via tftp working. Funny story - I was getting nowhere with it and then decided to tcpdump on the tftpd box, and wow! The UIP-200 tftp client was looking for the uniden<mac>.txt in lower-case! Hah! That was easy to fix. Now the config is transferred to the UIP-200 at startup. It registers to the * server. The phone displays time and

I am looking for a large number (probably about 100 or so) low-cost phones that I can hang on the wall. I need the phones to use PoE. Do the Uniden phones support wall-mounting? These phones are not going to be high-usage; they simply need to be there in case of an emergency. Another question, along the same kind of lines, has anyone figured out how to keep the SoundPoint IP 600 receiver

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in

The piece of plastic is built in to the IP600. Use a screwdriver or something similar and push the little piece of plastic out from the top inside the cradle. It will pop out, and you can turn it over and reinsert it upside down to hold the receiver in place. ________________________________ From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On

I need to purchase approx. 10 phones for a small office implementation. Nothing fancy is required besides a full-duplex speakphone, in the sub-$200 range. I am currently looking at the Polycom Soundpoint 500, Uniden UIP-200 and SwissVoice IP-10. I have searched around and found various posts regarding each phone's ability to work with asterisk (SIP, I probably should have mentioned), but

Hello, This is not exactly an Asterisk question, but I was encouraged to seek advice here anyway. The kindness of the * open source community is legendary :) I am getting going with an Asterisk 1.2 box, and I'm having trouble getting good quality transmit sound using handsets with VoIP phones. I'm primarily trying to focus on SPA-941, but also experimenting with Aastra 9113i and Uniden

I have a dilemma. I am trying to setup an asterisk setup for about 10 people, but with the ability to expand to 100s. We are looking into hardphones to use for our systems. Here are the requirments I am looking for: SIP Not POE Full duplex Speakerphone $100-$300 We would like to have the cordless and corded option if possible (at least for 3 of the 10 people). So here are the

Does anyone know if it's possible to set the codecs for a number via an Asterisk command? Ie, yes you can set the codecs in sip.conf for a user, but I'd like to have a command that can set the same thing so that it can be done without having to change sip.conf. Essentially I want the user to be able to prefix a code to their dialled number to set their preferred codec for that call.

Does anyone know how (if possible) to do three way calling on the UIP-200? There doesn't seem to be much info about this phone, but all the feature lists I've read says it can do conference calls. I can't seem to do it, though. Any help would be appreciated. -- Seth "et lux in tenebris lucet" Mattinen sethm@rollernet.us

The UIP(update in progress) is set when RTC is in updating. And the update cycle begins 244us later after UIP is set. Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com> diff -r 47cb862a07c2 -r edc35b026509 xen/arch/x86/hvm/rtc.c --- a/xen/arch/x86/hvm/rtc.c Mon Mar 05 14:39:07 2012 +0800 +++ b/xen/arch/x86/hvm/rtc.c Mon Mar 05 14:39:41 2012 +0800 @@ -28,6 +28,8 @@ #include

Anyone using the UIP200 with *? I am having difficulty getting the phone to register and *stay* registered for more than 4 seconds. The * console shows the UIP200 registering and records the user agent. The UIP200 displays station name and time on its LCD, then 4 seconds pass and it shows #1 DISCONNECTED. The * console reports no problem and believes the device to still be registered. A call