similar to: SIP Debug

Hello, I am trying to setup a Grandstream GXP2160 IP-phone with secure calling (SRTP). Secure signaling SSIP for registration is working great ! I follow this guide : https://wiki.asterisk.org/wiki/display/AST/Secure+Calling+Tutorial But when I try to make a call with SRTP, I get stuck. There is an initial INVITE which is anwered with a 401. There should follow a new INVITE with a nonce,

We have a basic application that runs a SIP channel to pick up a call and process it. We are using Broadvoice and it's been working great. We recently rebooted the machine and now when a call comes in Asterisk picks up the call but does not process it. Asterisk seems to send the call back to Broadvoice. Nothing at all has been changed in the configuration to warrant this. Below is the

I'm new to asterisk and need some help with getting a SIP connection working. I am trying to establish a termination point/DID number in another country. I am currently running Asterisk CVS-HEAD. My foreign provider uses SIP and authenticates via IP address. I am not required to register my SIP connection in order to send or receive calls. Can someone help me with how to understand the

Hi, I have 2 systems (A and B). I have an 800 number... when someone calls the 800 number it goes: IAX2-->A---IAX---B--->SIP PHONE However.. if the user calling the 800 number is a SIP user that is registered to A it goes: SIP--->A---IAX---B--->SIP PHONE This is the problem... when a call comes in from the IAX2 800 provider, things work fine... however if a SIP user registered to

Hi, I've one Sipura SPA2000 at home behind a linuxbox with two network adapters (eth0 for WAN and eth1 for LAN) doing NAT/DHCP: ___________ HOME _______________ ____OFFICE ____ SPA2000 <---> Linux Box <--> Asterisk Box 192.168.0.253 192.168.0.1 eth1 200.93.xxx.a 200.93.xxx.b eth0 My problem is when I try to call to any trunk or extention

I am trying to make PJSIP work with my Cisco SPA504G phone. I have no problems making it work with the chan_sip driver. When I configure my phone, it indicates the contact was added -- Added contact 'sip:7001 at 192.168.9.142:5063' to AOR '7001' with expiration of 3600 seconds Phone shows green light for the line. I then attempt to dial extension 1 and Asterisk crashes.

I'm communicating a softphone (SJPhone) to a Grandstream phone GXP-2000. The codec order on each one is the next: SJPhone: GSM - iLBC - PCMA - PCMU GXP2000: G729 - GSM - PCMA - PCMU (I have a G729 license, so there's no problem with transcoding G729) In my sip.conf, I've defined the following codec order: disallow=all allow=g729 allow=gsm allow=g726 allow=alaw allow=ulaw And my

OK, it stopped working. It turns out the transport and endpoints in PJSIP are ok. I can send an invite from my unregistered snom phone and I can see some activity in the CLI. However, when I dial from my snom to Kamailio and have it pass the message to asterisk, PJSIP seems to ignore the sip messages even though they are there. Is there something wrong in the invite that I'm missing? U

Hi, I have a strange problem. At a site where there are 20+ phones, there is one phone that cannot make outbound (to PSTN) calls. Each call is dropped after 20s with "no response to our critical packet". Calls to voicemail and internal extensions work fine. I understand that everything points to a NAT problem, but I don't understand how it could be because: 1) It does not affect

ping times are fine as well: [root at freepbx asterisk]# ping sipgate.de PING sipgate.de (217.10.79.9) 56(84) bytes of data. 64 bytes from sipgate.de (217.10.79.9): icmp_seq=1 ttl=57 time=46.7 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=2 ttl=57 time=46.4 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=3 ttl=57 time=46.7 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=4 ttl=57

hi, let me explain in detail, what i have configured and what is happening now: 1st router w724v (Deutsche Telekom AG): - port forwarding, everything to destination port 51000-55999 to device with ip 192.168.2.50 (interface of 2nd router) 2nd router Bintec RS353j): - configured NAT, everything to port 51000-55999 to device 192.168.3.99 (same ports) other direction is totally open. I

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

Hi, I'm trying to setup snom 710 phone with asterisk 13 with PJSIP. inbound is working fine but i cannot dial out. i don't hear anything on the phone and asterisk CLI also does not show anything. my config is. please advice. [2001] type=endpoint context=out-local disallow=all allow=ulaw allow=alaw transport=system-udp auth=2001

I have spent the morning on this project, still without success. Summary: Yesterday I inadvertently unplugged my Grandstream phone. I might add I did a rebuild of my s/w from CVS at the same time. Since then, the Budgetone seems to talk SIP just fine, but the RTP being sent to it by asterisk "doesn't make any sound." It was suggested I do a factory reset of the phone, which I

Surely there must be someone here who can help me with this problem. I have spent weeks trying to get this damned service to work with no luck. I have incoming calls working, but no outgoing. If get outgoing working then incoming don't work. I have sent this problem to this list a couple of times with little or no response, and I _really_ need some help to sort it out. I have an asterisk

Hello. I am in a strange situation. I have two asterisk. Asterisk "A" makes a call for asterisk "B" by IAX. Asterisk "B" recives the call and delivers it to Openser by SIP. The problem is openser printing this in the screen: ERROR: parse_to : unexpected char ["] in status 5: <<"David" <sip:>> . ERROR:parse_from_header: bad from header

Le 09/09/2016 ? 18:32, Madushan Geethanga a ?crit : > Hi, If you're not using RTP encryption did you uncheck the option in your RTP TAB from identity ? > > This is the log. ex dialling 0 from snom phone > > > <--- Received SIP request (1230 bytes) from UDP:123.231.72.210:33878 > <http://123.231.72.210:33878> ---> > INVITE sip:0 at 54.206.59.252

Hello everyone, Well here is my initial posting to the list, and I will admit Asterisk is new to me. I just got everything running here a couple days ago, so still learning the ropes for sure. OK, here is my problem. Currently I have it setup talking to a couple Cisco IP phones, and some Xten softphones, this works great. I also got an account with FreeWorld Dialup using IAX2 and that

Hello, a person trying to call me by my phone number is getting the error 488 Not acceptable here. I googled that error, seems like this error is normally caused by a failed codec negotation, though I have no clue how I could have read this out of the logs. Anyway, my setup is as follows: Asterisk 1.8.13.0 - NAT - Sipgate SIP Provider The user calling me is also using Sipgate and is calling my

Hello: I have this situation: I can make calls internally, I can make inbound calls but I can't make outbound calls. Thanks in advance. These are my devices: * asterisk 11.8.1 = 192.168.1.22 * sipphone grandstream gxp2160 = 192.168.1.5 * gateway audiocodes mp-114 2fxs-2fxo = 192.168.1.4 port 1 (FXS) connected to an analog phone port 3 (FXO) connected to the PSTN These are my