similar to: "Cannot native bridge" on licensed G729

Hi, I am trying to post this again as I am getting no answers and the support@digium.com bounces... (I have searched the whole list and can't find the answer either) I have installed a 5 user license for G.729 and want to route calls through Asterisk from my G.729 phone to Cisco AS5300 also using G729. Both Cisco and the phone connect using this codec if I do not force the call to go

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

Hello everyone. I'm struggling to get T.38 faxing to work in Asterisk 1.6.1.13 with a SIP DID provider here in Brazil (GVT - Vox IP service). Here's my scenario: When faxes arrive by a specific DID, they are routed thru this simple macro: [macro-recebefax] exten => s,1,Set(DB(fax/count)=$[${DB(fax/count)} + 1]) exten => s,n,Set(FAXCOUNT=${DB(fax/count)}) exten =>

Hi everyone! Situation: when I call from cell phone to a asterisk-connected phone, all works fine. When I call from the asterisk-connected phone (a Cisco 7960 SIP) to the cell, the connection gets made, but there is no audio going in either way... Asterisk reports the following: Sep 16 08:27:41 WARNING[245775]: chan_sip.c:2679 process_sdp: Insufficient information for SDP (m = '', c =

Dear i have buy two license of G729 codec and i have install/registered as documented but after i start "Asterisk -vvvcng" i notice this warning and if i made call the CLI say "No compatible codec!" How can i solve this problem? Thanks in advance Dimitri ------------------------------------------ [app_datetime.so] => (Date and Time) == Registered application

Hi, I have a Cisco 5300 which I want to make a call THROUGH the Asterisk PBX (security) to an IP phone which supports g729, and vice versa. Both Cisco and the phone talk this codec if I do not force the call to go through * However if I say canreinvite=no in the sip.conf for either of these gadgets, the call will fail with No compatible codecs! I have bought a 5 user license just to

Hi, I've upgraded my asterisk 1.4 to the version 1.8.11. After making some adjustments to the configuration files to port it to the new version, calls between registered phones in asterisk, work fine, but inbound calls coming from the SIP trunk I have with a telco to asterisk, don't work anymore. I don't know why!... This is the SDP portion that comes in the INVITE messages of calls

Hi All, I'm trying to upgrade asterisk server to 1.8.x from my asterisk 1.6, But when making A Call from SIP Client, I got cli Warning ... and no call has been made. My Sip Client is using lib java peers client http://peers.sourceforge.net/ with standard codec PCMU/PCMA [Jan 28 23:03:32] WARNING[1654]: chan_sip.c:8942 process_sdp: Unsupported SDP media type in offer: audio 0 RTP/AVP 0 8

hey, I bought a license for 729 but I can't use it this is the message. == Registered translator 'g729tolinb' from format 8 to 6, cost 99999 == Registered translator 'lintog729b' from format 6 to 8, cost 18 == Parsing '/etc/asterisk/enum.conf': Found Asterisk Ready. *CLI> WARNING[5126]: File chan_sip.c, Line 1601 (process_sdp): No compatible codecs!

Hi, as stated in the documentation, it's allowed to set FAXOPT(faxdetect)=yes/no to allow fax detection. It's done (see below) but still fax detection :-( Extension 300 is hylafax with iaxmodem. On the upper Asterisk gw it's the same, despite the faxdetect set to no we also have the NOTICE of T.38 re-INVITE. Test is done with a mobile phone calling the 0123456789 PSTN number.

hi, is there someone with working asterisk13+chan_sip+SIP.js/sipml5 ? or is chan_pjsip better supported? or the recommended way for asterisk is use respoke.io? my problem with asterisk13+chan_sip+sipml5(the same problem is with SIP.js) chan_sip.c:10496 process_sdp: Can't provide secure audio requested in SDP offer " sip.conf (important parts) [vr1a882] ... nat=force_rport,comedia

I solved the issue by not answering the call as I assume others have done. -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Administrator TOOTAI Sent: Wednesday, February 18, 2015 12:50 PM To: asterisk-users at lists.digium.com Subject: Re: [asterisk-users] Res_fax - FAXOPT(faxdetect) Hello Le

Retrying, falling of the list some how :-( -------- Original Message -------- Subject: feeling n00b again Date: 2018-08-20 09:51 From: asterisk at a-domani.nl To: asterisk-users at lists.digium.com Hi all, Long time ago, I followed a Asterisk training, and both at work and at home, was able to deploy Asterisk, make all sorts of internal call (hard/soft voip-phones, incoming/outgoing,

Hi, I'm using asterisk 1.2.1. Is there anybody out there who knows what this warning means? *WARNING: chan_sip.c:3470 process_sdp: Unknown SDP media type in offer: image 5004 udptl t38* Google does not help at all. TIA Giorgio Incantalupo

Hi all! Quite a mystery. The following happened when I was on holiday, and no one else has changed any configs of either Asterisk or the Cisco's in the building... The situation: Incoming works fine on all phones. Outgoing only works from non-Cisco phones. When calling from a Cisco phone to an external phone, all the Cisco-user hears is a ticking crackle and after about a minute the phone

hi, all i want to use g729 codec for set up a call. so i donwloaded the so file from web site: http://asterisk.hosting.lv/#bin and install it properly. *CLI> *CLI> core show translation Translation times between formats (in microseconds) for one second of data Source Format (Rows) Destination Format (Columns) g723 gsm ulaw alaw g726aal2 adpcm slin

When I get a SIP call, I get the following error: *CLI> NOTICE[1133718080]: File chan_sip.c, Line 1768 (process_sdp): Content is 'multipart/mixed;boundary="unique-boundary-1"', not 'application/sdp' WARNING[1225991360]: File pbx.c, Line 1154 (pbx_extension_helper): No application '' for extension (incoming, 5147771111, 1) == Spawn extension (incoming,

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Anyone else have issues with T.38 where the call drops after T.38 is attempted to be negotiated, with a message like the below? WARNING[31046]: chan_sip.c:4978 process_sdp: Unable to lookup host in c= line, 'IN IP4 100101'