similar to: Running Asterisk on a Dell PowerEdge 2850 Server Re: Dell Hardware

It's Digium, not Dell. I have two identical Dell 1850s, each with the allegedly offensive built-in E100 Ethernet ports. I placed a TE410P card in each. One worked great, the other would not modprobe. Upon examination, we discovered that the two TE410P cards had different firmware revisions. Turns out the one with the older version was the one that worked. We sent the second card back

Guys. What do you think about Dell hardware and Asterisk? Whos using it, comments, any special specs recommended or models?

Hello, I have a Dell PowerEdge 2850 that periodically (6 times in the last 24 hours) freezes, requiring a power cycle in order to come back. The machine is running a Xen 2.0 stable source install. Here is the appropriate Grub entry: title Xen 2.0 / XenLinux 2.6 kernel /boot/xen-2.0.gz dom0_mem=131072 module /boot/vmlinuz-2.6-xen0 root=/dev/sda1 ro console=tty0 Dom0 boots happily, and new

I have an Asterisk system running on T1 PRI trunks using a TE405P. It seems to be running ok, but one thing puzzles me. Every so often I get a raft of messages like this: -- B-channel 0/1 successfully restarted on span 1 -- B-channel 0/2 successfully restarted on span 1 ....... -- B-channel 0/22 successfully restarted on span 1 -- B-channel 0/23 successfully restarted on span 1 I could

While running a multiple VM testscase with each VM running iperf traffic between others the following kernel NULL pointer exception was seen. Race appears when the tun driver instance of one VM calls skb_array_produce (from tun_net_xmit) and the the destined VM's skb_array_consume (from tun_ring_recv), which could run concurrently on another core. Due to which the sock_wfree gets called again

While running a multiple VM testscase with each VM running iperf traffic between others the following kernel NULL pointer exception was seen. Race appears when the tun driver instance of one VM calls skb_array_produce (from tun_net_xmit) and the the destined VM's skb_array_consume (from tun_ring_recv), which could run concurrently on another core. Due to which the sock_wfree gets called again

Hi my friends, I am running into a problem with my NIC. [root@xxxx ~]# ifup eth0 Error for wireless request "Set Encode" (8B2A) : SET failed on device eth0 ; No such device. SIOCGIFFLAGS: No such device Failed to bring up eth0. eth0 is not a wireless device. Below are some information about my host: [root@xxxx ~]# lspci |grep -i ether 00:04.0 Ethernet controller: Intel Corporation

Did anyone manage to have xen (3.0.1 stable) run on this config? (this is on FC4 if it matters). I''ve tried recompiling the xen0 kernel with the Fusion options from my current kernel added, but it keeps removing some of them (maybe some that didn''t exist yet in kernel 2.6.12), and it seems I end up without the correct driver. If someone has this running, I''d be

-----Mensaje original----- De: Mario Montiel [mailto:mariomontiel@grupocsi.com.mx] Enviado el: Viernes, 26 de Mayo de 2006 10:29 p.m. Para: Asterisk Users Mailing List - Non-Commercial Discussion Asunto: RE: [Asterisk-Users] DELL PowerEdge 2850 and TE4110P and TE110P I have many problems with this server and two cards TE4110P, because after several minutes one of two cards stays out without

I am trying to get the temperature of a Poweredge 2850 with CentOS 6.3 on it. Has anybody on this list done this successfully? Thanks -Surya PS: Apologies for cross posting if you are on the Poweredge list. -- Surya Saha Department of Plant Pathology and Plant-Microbe Biology Cornell University, NY, USA http://www.linkedin.com/in/suryasaha

Hi all, I got the previously mentioned Dell Poweredge 2850 with 4GB RAM and Perc4e raid controller. Installation went well and the raid is pretty fast even with level 5. However I have another problem now... CentOS 5.2 only sees 256MB RAM. Googling a bit, got me to install kernel-PAE, this went well, but CentOS still sees only 256MB. Googling some more, I found a bios update was suggested and

Hi all, We are running Asterisk 1.2.7.1 on our Dell Poweredge 2850 and are having massive sound quality issues. We are experiencing call quality issues for our remote location, namely calls cutting out and breaking up for our agents. The two main issues seem to be 'popping' and 'dropping' - popping would be pops and crackles on the line, where dropping would be complete audio

Hello, I'm having problems getting my samba setup to work at a little LAN i partially maintain. I've been reading quite a lot about what I could think of being related to my problems/setup, and I've also googled my ass off :( So here I am, resorting to you guys in hope of help =] Sorry to say, but I don't have much experience, and therefore I'm a bit lost at the moment. Not

On Wed, Dec 06, 2017 at 09:57:41AM +0000, George Cherian wrote: > While running a multiple VM testscase with each VM running iperf > traffic between others the following kernel NULL pointer exception > was seen. > > Race appears when the tun driver instance of one VM calls skb_array_produce > (from tun_net_xmit) and the the destined VM's skb_array_consume > (from

Hi, recently I came across a deal on a bunch of Dell PowerEdge 2850 servers and I was hoping to use them to run Debian with Xen to provided virtualization support for Windows 2003 and other Debian installations. I was hoping to install 2 copies of Windows 2003 as well as 2 copies of Debian all on top of the DOM0 Debian installation. The servers have dual 3.2ghz CPU''s and include 16GB

Hello, Digium uses the Dell PE 2850 for their testing. This site says that 3.3V PCI slot. http://www.voip-info.org/wiki/view/Asterisk+hardware We are planning on purchasing a Dell PE 2850 and putting a TE205P card on it. However, the needs a 5V PCI slot. Does Dell PE 2850 has a 5V PCI slot? A person in our group tried to call Dell's customer support but they do not seem to know.

Hi All Before I go out and buy a DELL PowerEdge 2850 has anyone had problems (or any other useful experience) getting a TE411P to work with it. I also have a legacy TE110P. Has anyone had problems with this combo. -- Dr. Rodney G. McDuff |Ex ignorantia ad sapientiam Manager, Strategic Technologies Group| Ex luce ad tenebras Information Technology Services | The

Hi I have installed CentOS 5 on my computer which has an Intel ICH5 sound chip. The card appears as it should, and I can adjust the volume just fine. However, when I try to play a sound file(.ogg for instance), rhythmbox plays through the file, but no sound is heard. I've tried as root, and I've tried doing cat /dev/urandom > /dev/dsp, and it's all quiet. Output from lspci:

Hello I have a problem to boot my xen kernel, I have a debian sarge 3.1 stable, download xen-3.0.2-src.tgz, extract and compil it with the command "make world" But at boot I have an error : "cannot open root filesystem sda1" My raid controler is a perc4/di raid 5 controler lspci -v said : 0000:02:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 4 (rev