similar to: re: DTMF woes, continued

hello, after playing with an asterisk configuration for voip for a few weeks i'm trying to get outbound dialing with voicepulse going - i've cut down the asterisk to a very minimal install (1 SIP client) to try to localize the problem. The SIP client works fine (SIP and * on the same NAT) and could access the demo from samples before i removed it, and can call itself - so i am

hi all, I keep asking the question and getting no replies, so i'll keep asking :-) In asterisk 1.09, with autocreatepeer=yes, if i send asterisk a SIP request from SER, specifically rewritehostport("myIP:5070"); (asterisk running on port 5070) asterisk picks up the request and matches it to the dialplan, i.e. if in ser i was sending to 151@myServer, it will make it

hello all, i need some help and after trying the wiki i'm even more confused than i was. i'm trying to set up call forwarding and running into problems... i want the most basic call forwarding imaginable. 1. caller dials extension (say, 154) 2. dialplan is updated to forward caller's extension (based on CALLERIDNUM) to voicemail, instead of ringing his endpoint. 3. caller is

We are using a platform from AmarFone Inc. It great full featured , everything you want to run a calling card and does not cost your a lot of money. Their support is awesome. You can contact them at sales@amarfone.com. Ehsanul Karim

Hi Yair, Please let me if you managed to fix the DTMF tone issue, which you were experiencing couple of months ago. If not can you share any advancement. I'm currently experiencing the same issue, I can make outbound calls but DTMF will not work when dialing IVRs. My configuration is asterisk@home 1.5, registering to Voip provider (Symbio), codec is g.729 and dtmf mode is set to rfc2833.

Hi all, i'm trying to integrate cepstral and asterisk, and i have a problem i'd appreciate any help with (i know it's a bit tangential, but i figure this is the place with the most knowledge of app_swift and asterisk). I've installed swift from cepstral.com with alison's voice, and it works fine, from the command line i can do swift "hello there" -o test.wav and then

hi all, you'll have to excuse the ignorance (i'm a software guy, not a telcom guy..) Is there any way to know if a channel has been answered by an automatic system (like voicemail) rather than a human being? Specifically, I want to use a .call to make a call on a channel and only do something if a person answers, not a machine of any kind. Is this even possible, or is an answered

Hi all I have a couple of questions maybe you guys can help me with them I have sip phones , SER server , Asterisk. what is the best way to do that (also with accounting and authentication). which one of those options 1) sipphone -> SER -> ASTERISK -> SER -> PSTN 2) sipphone -> SER ->ASTERISK ->PSTN on the first option i am trying to return the call to the ser

Hi guys, I have a weird thing happening sometimes with users calling from a GrandStream phone through Asterisk onto a PSTN. Sometimes after a user hangs up a call on a GrandStream phone the phone starts ringing after a couple seconds. When the call is answered there is no one there. Anyone had this before ? Kindest regards David Wilson _______________________________ D c D a t a Tel +27 33 342

Hi List, I'm using VoIPJet and NuFone as a fallback, and it seems that both of them are circuit busy! Also it seems that VoIPJet takes forever to return 'circuit busy' while NuFone does it instantly. At any rate, is there like a reliable third VoIP provider I can use for fallback when the two others are busy? Cheers, Jean-Michel.

Hi, I'm new to Asterisk and I've been trying to configure it to talk to several SIP providers (such as FWD). I found that, although there are some "recipes" on how to do it, there are few documents that really explain *why* the settings are used, and overall I found very little documentation on sip.conf. I've been using this page as a reference:

Ronald, Grandstream products have a one year warrantee. If you don't have any luck with Pulver, contact us and we can probably get your phones exchanged. Please don't assume that your experience with Grandstream is typical. We sell a lot of these phones and the overwhelming majority of the purchasers are very happy with their units. The quality has improved tremendously over the last

Greetings. I'm having a bit of a problem using the sipdtmfmode app. I have two incoming paths to * from pstn via FWD that use differing dtmfmode. IPKall wants rfc2833, libretel wants inband. If I set dtmfmode= in the fwd peer config in sip.conf each works seperately, and I'm trying to use gotoif and sipdtmfmode to switch based on the CID calling. Output seems to indicate sipdtmfmode

hello all, i have a problem, and i'm tearing my hair out...any assistance is appreciated. I am trying to redirect from SER to Asterisk, both on the same machine. In 1.09 I didnt need to set up a peer for SER, just autocreatepeer=yes, and rewritehostport from SER as below, and asterisk accepted the requests without a problem. When I updated to 1.23 requests from SER to asterisk die quietly, no

I can smile now. I made my * work with my Cisco. Finally. First problem was Ethernet on my Linux. After installing * on a different machine, I got rid of that "icmp udp unreachable" error. My next problem was the call stays on on Cisco gateway, but the ATA drops it. I figured out it was my mistake on dialplan in extensions.conf --- (it took me a day to notice it.. damn!). my config

All, Here's a cool one.. I was attempting to call a retarded conferencing service, and was having problems with it picking up my DTMF.. after trying all the settings my Sipura SPA2000 offers, I found inband actually works.. unfortunately, I can't get anything else to pick up my inband DTMF (including asterisk's builtin voicemail! It just times out and says I never entered a login!).

hi list, is anyone succesfully using asterisk with libretel port-of-call (www.libretel.com)? If so, i would be grateful for configs..i set up libretel to forward to mynumber@myserver.com:5070 (asterisk is running on 5070 and SER on 5060) and when i call the number i see SIP messages with ngrep but the asterisk CLI doesn't seem to catch them. I assume i need to register...is this even possible

Hello how can I set the fromuser field of the SIP INVITE when using the Dial()-command in the dialplan ? None of the below Dial() command give the correct result : exten => _XX.,n,Dial(SIP/${EXTEN}:passwdk5j6::user762 at myprovider.biz) exten => _XX.,n,Dial(SIP/${EXTEN}:passwdk5j6::user762 at myprovider.biz/${EXTEN}) exten => _XX.,n,Dial(SIP/user762:passwdk5j6::user762 at

Hello a call goes out and is answered : [Sep 17 11:29:52] VERBOSE[23420][C-00000051] app_dial.c: SIP/myprovider-0000010b is making progress passing it to SIP/mysippeer-00000108 [Sep 17 11:30:05] VERBOSE[23420][C-00000051] app_dial.c: SIP/myprovider-0000010b answered SIP/mysippeer-00000108 [Sep 17 11:30:05] VERBOSE[23522][C-00000051] bridge_channel.c: Channel SIP/myprovider-0000010b joined

In the following example exten => _1NXXNXXXXXX,1,Set(GROUP(outbound)=myprovider) exten => _1NXXNXXXXXX,n,Set(COUNT=${GROUP_COUNT(myprovider at outbound)}) exten => _1NXXNXXXXXX,n,NoOp(There are ${COUNT} calls for myprovider) exten => _1NXXNXXXXXX,n,GotoIf($[ ${COUNT} > 2 ]?denied : continue) exten => _1NXXNXXXXXX,n(denied),NoOp(There are too many calls up) exten =>