similar to: DTMF with Asterisk as SIP client

Hello, I am new on asterisk and do some tests on freepbx. I have 2 SIP provider: Provider1: In-/Out- Flatrate, only 1 Number Provider2: Incoming Flatrate, Outgoing Cost depend on destination, 3 numbers On Asterisk site i have 3 phones (branch ??, don't know how its called in asterisk) Is it possible to do something like: Phone 1: Incoming Call: Number1/Provider1 Outgoing Call:

Kevin Larsen - Systems Analyst - Pioneer Balloon - Ph: 316-688-8208 asterisk-users-bounces at lists.digium.com wrote on 12/14/2017 09:36:06 AM: > From: "basti" <mailinglist at unix-solution.de> > To: asterisk-users at lists.digium.com > Date: 12/14/2017 09:36 AM > Subject: Re: [asterisk-users] Rewrite Outgoing Number > Sent by: asterisk-users-bounces at

Hi :) I hope someone has a hint concerning Early Media. The situation: My Asterisk is connected to small local carrier who works with several SIP servers. I traced some SIP headers and find something like this: Via: SIP/2.0 UDP sip1.provider1.de In the SDP part I found something like this: o=- 2268929 0 IN IP4 sip2.provider1.de c=IN IP4 sip2.provider1.de If I send

Greetings all, I'd like to start implementing a private DUNDi peering group between one of our asterisk servers hosted at a datacentre and the various asterisk boxes sitting at clients' premises. On most of the clients' boxes the dialplan will have an [in-pstn] section containing the various numbers that should be recognised by that box. Where they're from a VoIP provider they

Hello everyone. I've stumbled upon a strange networking issue with multiple interfaces on CentOS 5. The network setup is just like the diagram in http://lartc.org/howto/lartc.rpdb.multiple-links.html It looks like linux is not routing correctly outgoing packets on interfaces different from the one of the default gateway, but instead broadcasts an ARP request on the link, looking for the

I am using GotoIf all over the place in 1.4.8 but for some reason, the following in my dial plan: ############################################################# exten => _1NXXNXXXXXX,1,GotoIf([${EXTEN} = "15554441212"]?100) exten => _1NXXNXXXXXX,n,Dial(SIP/provider1/${EXTEN},60) exten => _1NXXNXXXXXX,n,Dial(SIP/provider2/${EXTEN},60) exten => _1NXXNXXXXXX,n,Hangup exten =>

Hello In the LARCT how-to subitem: 4.2.2. Load balancing the following phrase says: "" Instead of choosing one of the two providers as your default route, you now set up the default route to be a multipath route. In the default kernel this will balance routes over the two providers. It is done as follows (once more building on the example in the section on split-access): ip

Hi, I put on sip.conf the following line #include "sip.d/*.conf" inside I have files like that provider1.conf provider2.conf But asterisk does not want to load it This is the error Sep 1 13:18:35 VERBOSE[8756]: == Parsing '/etc/asterisk/sip.d/*.conf': Sep 1 13:18:35 VERBOSE[8756]: == Parsing '/etc/asterisk/sip.d/*.conf': Not found (No such file or directory) this

Greetings list, Over the last few days I've been gearing up to replace a couple of our servers with 1.6 as something of a testbed, but I'm encountering a few problems, and wondering if anyone can help... In extensions.conf, there are a number of contexts defined for each group of users, along the lines of: [groupa] [groupb] etc. In each of those, there's a command include =>

hello, after playing with an asterisk configuration for voip for a few weeks i'm trying to get outbound dialing with voicepulse going - i've cut down the asterisk to a very minimal install (1 SIP client) to try to localize the problem. The SIP client works fine (SIP and * on the same NAT) and could access the demo from samples before i removed it, and can call itself - so i am

Hi, I''ve been experimenting with ip route for the last few days to get load sharing accross 2 providers working. While it works most of the time, on a few occasions, packets are routed to the wrong interface. I''m not sure to understand rules and routes traversal correctly (I couldn''t find answers in the howto). So, here are my questions: 1. How does the rule

hello all, i need some help and after trying the wiki i'm even more confused than i was. i'm trying to set up call forwarding and running into problems... i want the most basic call forwarding imaginable. 1. caller dials extension (say, 154) 2. dialplan is updated to forward caller's extension (based on CALLERIDNUM) to voicemail, instead of ringing his endpoint. 3. caller is

How do you setup the timing in Meetme conference? I have a x100p and tdm4x card. When I dialing to my conference I get a request to schedule in the past error message. thanks -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Saturday, April 10, 2004 10:48 AM To:

We are using a platform from AmarFone Inc. It great full featured , everything you want to run a calling card and does not cost your a lot of money. Their support is awesome. You can contact them at sales@amarfone.com. Ehsanul Karim

Hi all, i'm trying to integrate cepstral and asterisk, and i have a problem i'd appreciate any help with (i know it's a bit tangential, but i figure this is the place with the most knowledge of app_swift and asterisk). I've installed swift from cepstral.com with alison's voice, and it works fine, from the command line i can do swift "hello there" -o test.wav and then

hi all, you'll have to excuse the ignorance (i'm a software guy, not a telcom guy..) Is there any way to know if a channel has been answered by an automatic system (like voicemail) rather than a human being? Specifically, I want to use a .call to make a call on a channel and only do something if a person answers, not a machine of any kind. Is this even possible, or is an answered

Hi all I have a couple of questions maybe you guys can help me with them I have sip phones , SER server , Asterisk. what is the best way to do that (also with accounting and authentication). which one of those options 1) sipphone -> SER -> ASTERISK -> SER -> PSTN 2) sipphone -> SER ->ASTERISK ->PSTN on the first option i am trying to return the call to the ser

hi all, I keep asking the question and getting no replies, so i'll keep asking :-) In asterisk 1.09, with autocreatepeer=yes, if i send asterisk a SIP request from SER, specifically rewritehostport("myIP:5070"); (asterisk running on port 5070) asterisk picks up the request and matches it to the dialplan, i.e. if in ser i was sending to 151@myServer, it will make it

Hi! I'm really hope you can help me solve a little mystery, the mystery is probably just my misunderstanding ! sorry... I've got an iaxy talking to my * box which connects to two providers. I'm running the stable release of the pbx. The only thing is that when dialling from the iaxy the ringing tone isn't heard while calling someone - you just hear silence then, they either

Hi guys, I have a weird thing happening sometimes with users calling from a GrandStream phone through Asterisk onto a PSTN. Sometimes after a user hangs up a call on a GrandStream phone the phone starts ringing after a couple seconds. When the call is answered there is no one there. Anyone had this before ? Kindest regards David Wilson _______________________________ D c D a t a Tel +27 33 342