similar to: RTP not thru asterisk

Hi all, This is the first time i am using stun with asterisk for nat problems. I have read the rfc which describes how stun works. i didnt have any problems understanding it. I have also intalled the stun server called stund which i downloaded from sourceforge. I have seen on the list that most people use stund here. I have started the stun server and its running silently. Now i dont know what to

I have three video phones here for testing: Extension 6003 is Eyebeam Extension 6004 is a hard phone (model 8770) Extension 6005 is a hard phone (model 8882) Can anybody have a look at my settings and the output I get from all kinds of dialings, please. The sip settings for all phones is (user / password different): [6003] type=friend username=6003 secret=pwd qualify=200 nat=yes host=dynamic

Hi, I tested the capi_chan with latest cvs of * and I have problems with Early-B3. The following dialstring works for me (without Early B3): exten => _0X.,1,Dial(CAPI/@22715291:${EXTEN:1}|30) But if I add the 'b' for using Early-B3 exten => _0X.,1,Dial(CAPI/@22715291:b${EXTEN:1}|30) nothing changes (no dialtone). If in this example the called party discards the call, there is no

Hi guies, I know I know this subject have been The most written subject about VoIP Right... but I just want to make clear, just one time ! If Asterisk is on a Public IP Address and a softphone behind the nat, sip.conf must contains for this phone: nat=yes .... Now if I want to configure my sipphone (X-Lite) placing behing the NAT, it must have in "Domain/Realm" the external IP

Hello All, Currently my setup uses Xlite and Asterisk and i found that all the RTP voice packets are transfered via the asterisk server from one xlite to another. Is there any possibility that we can make all the RTP Packets to be transfered directly between the two clients once the connection is established?. Any one please help me. Thanks and Regards, Senthil Murugan.V

Should the following setup work? SIP UA---NAT---Internet---NAT---SIP UA If both UA's support STUN and report the external IP address in the SIP packet.. I am trying to get away from using canreinvite=no so that traffic can go directly between the UA's and not via the central server but I can't seem to get it to work.. Has anyone set this up and can give me some pointers??

Guys, I've been poking around trying to find a good answer for this via voip-info, google, etc... Haven't found anything that helps, so maybe you mates could. A lot of my customers are using Linksys UAs (router/ATA PAP2) and some using Sipura SPA-2002s. Every once in a while, the customer will get one-way audio. I've read that this is commonly caused by the outgoing RTP port not

I've been reading up on the SIP and related (SDP/RTP) RFC's and as I would expect the RTP session should ideally be between the two end points of the call, in my case the AS5300 and the 7940 which are connected on the same VLAN as the Asterisk server. When I sniff the packets on the VLAN I find that all RTP packets are being relayed by the Asterisk server causing increased load on the

Guys. Im writing this because Ive checked the wiki, Xten website and read a lot of docs and still cant figure out a way around the NAT issues. Maybe somebody else can give me some ideas from a fresh perpective. My test setup is this: Asterisk -> 2wire homeportal Firewall -> internet Computer with Xten eyebeam The asterisk box and the computer with xten beam are behind the same

so, is it safe to put canreinvite=yes on a 7960? on a 1750? on a spa-x000? an xten? how the heck do i find out other than the hard way? randy -- ps: pun intended

I am trying to get a SPA-3000 to work behind NAT - for the sake of the exercice. The SPA is on the local network at the address 192.168.0.125 behind a NATted linux router. The machine I am trying to work with is a friend's (let's call it lolo.dyndns.org) and I've installed Asterisk 1.0.3 on it. I can see the SPA register but when I try to make an outbound call I get the message:

Hello Folks- Pretty new to the list here, got a lot of reading to do.. Does anyone know where I can find a decent HOWTO or set of instructions for running Asterisk and SIP clients thru firewall/NAT systems? I have a Asterisk box sitting behind a linux firewall at a remote location and have the 5060 and etc ports open as well at 16381-16391 UDP open and routed to the Asterisk box as well. I have

pstn -> sip gw -> * -> C7960 When I dial into * via the pstn, I hear the ivr menu just fine (good quality). I press 3000 (valid extn), and I begin to hear ringing however the ring back is very very choppy. I answer the C7960, and speech is clear in both directions. Place the C7960 extn on hold, and the MOH is very choppy. Checking 'sip show channels' indicates both the sip gw

Hi, I install * and is working fine. I have 3 FXO cards w/ 3 phone lines. All the phones are SIP phones (Grandstream). The SIP phones from the same LAN w/ Asterisk are working but on the external phones (from the Internet) I don?t have sound. All the Grandstream phones from the Internet are register from different locations behind a NAT. All the sip users are register on * but the main issue is

The asterisk server has a permanent IP address, but the provider cannot ensure stable quality traffic for RTP. There is a desire to use an external server, the address of which shall be specified in the SDP, through which flowing media. I use asterisk 13.6 and res_pjsip. Prompt, please: 1. what software can be used on an external RTP proxy? 2. What settings need to be done in pjsip.conf to use

Hi, I'm having a problem with my asterisk, trying to connect to a CISCO 2840 IOS12.x ASterisk is behind firewall NATing, when it do the handshaking for RTP, it sends his internal IP instead of sending the external one. How can I tell the asterisk box, to modify that and send the external IP? I tryied with Sip.conf's externip=xxxx and localnet=xxxx, nat=yes Nothing seems to change the

Asterisk is on public IP (as described in the first email) i have 10 years experience in voip, 4 years webrtc in production. i know about ICE/STUN/DTLS-SRTP. yes, not every detail but the basic mechanism but i confess. i dont understand WHY Asterisk SOMETIMES switches destination IP in RTP. this is not only about ICE. its about RTP engine too which is Asterisk specific and Asterisk DEBUG is

hi, i have following topology PSTN - Asterisk ---- internet -----  router - jssip client (wss) Asterisk 13.29.1 on public IP, chan_pjsip for wss, chan_sip/udp for SIP connection to PSTN router - public IP/private IP (NAT) jssip client - private IP - sip over websocket to Asterisk PJSIP ~30% of calls has problem with no audio. reason is that Asterisk is sending RTP to private IP of jssip

Hi all, is it possible to monitor RTP protocol (latency, errors, ...) by Asterisk or other software. Thanks for answer, Bob.

Hello. Is someone here using VoIPmonitor? I am using just the sniffer and I found some pcap files that contain some odd streams. For example, I have a file with 3 streams, but the weird stuff is that 2 streams are the same (e.g., have the same source address and port and same destination address and port). Example: "Source Address","Source Port","Destination