similar to: SIP dialout

I previously posted about this problem and received suggestions involving turning off echo cancellation. As far as I can tell, echo cancellation is already disabled on this channel, so I'm back. What I've got is a small home setup with a single four-port Digium card: Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO Module 2: Installed -- AUTO FXS/DPO Module 3:

tnaks for your response but the number dialed exist and i can call this number when i configure the trunk directly in x-lite and i call call also this number from my cell phone . any help thanks and regards 2015-03-25 12:59 GMT+00:00 Matthew Jordan <mjordan at digium.com>: > On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit > <salah.elharit200 at gmail.com> wrote: > >

On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit <salah.elharit200 at gmail.com> wrote: > hello list, > > i have asterisk 11.15.0 and i have some trunks sip from my provider > > we have some ip phone astra 6731i > > each Ip-phone is configured with trunk and we call > > no ihave configured another trunk from the same provider in my asterisk > > i can call

hello list, i have asterisk 11.15.0 and i have some trunks sip from my provider we have some ip phone astra 6731i each Ip-phone is configured with trunk and we call no ihave configured another trunk from the same provider in my asterisk i can call all numbers just the numbers are configured in thses ip phones. but when i configured the same trunk in x-lite i can call theses ip-phones without

Hello All. I am stumped, please help me out.. I have the following setup: VOIP provider = VOIP GW (asterisk GW1) = VOIP server (asterisk - VS1) The gateway is there to get around the limitations running on the VOIP server. I can call out from and receive calls VS1 no problems at all. However, when I try and redirect an inbound call out via the GW, it drops out. I have found that if I

Hi everybody. I have been searching and trying for an answer, but no luck, so here I go.. Is there anyway to execute multiple commands on a single priority in extensions.conf? eg: exten => X.,1,Dial(SIP/1111) & somefunction(${EXTEN}) I need the dial command to dial internal extensions, and the "somefunction" to kick of our own outgoing system for redirection to outside lines;

I am making some assumptions, but assuming the 217.195.xx.xxx is your provider, you are getting this back from them: "Got SIP response 556 "No address found" back from 217.195.xx.xxx:5060" Are you sure that "0033149xxxxxx" is the format the provider is expecting? You might try enabling SIP debug on the 217.195.xx.xx IP and seeing what the INVITE looks like, but

thanks for your response i noticed that when i active the voicemail in the IP-phone where the number 0033149xxxxxx is configured i can call this number without issue the server asterisk and the ip-phone where the number is configured are in the same network 192.168.1.X Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Called SIP/FD/0033149xxxxxx == Begin MixMonitor Recording

Hi, I am having some trouble with ISDN Dialout. Using a Netjet-s PCI Card. When in Minicom, the only way I can dialout is if i issue ATS18=1 First. Otherwise I get a BUSY message. So thats fine. But when I dialout from asterisk, I get an immediate hangup, so my guess is that asterisk is not issuing ATS18=1 to the ttyI device. Here are my configs, any input would be greatly appriciated.

Hello my name is Ilija Poznic and I have a problem. My configuration is 1. Digium TDM4000P with one FXS. 2. AVM Fritz ISDN adapter (configured with capi). When I connect to my ISP and then start *. Asterisks is registering me to SIP provider iconnect. After that I can call international call trough VoIP. My problem is that I want to dialout to ISP only when I have a international call.

Hi, I kludged support for the TrippLite SU2200XLA into nut-2.4.3 as follows: --- ./drivers/tripplite-hid.c.0 2010-03-03 15:53:20.000000000 -0500 +++ ./drivers/tripplite-hid.c 2010-03-03 15:53:40.000000000 -0500 @@ -81,6 +81,8 @@ { USB_DEVICE(TRIPPLITE_VENDORID, 0x4002), battery_scale_1dot0 }, /* e.g. TrippLite SmartOnline SU1500RTXL2ua */ {

Hello All. I am trying to use RAGI the ruby agi framework with trixbox. I am having a problem with the dialout part. The RAGI framework creates a file in the /var/spool/asterisk/outgoing directory and routes the call to an extension (I have listed the relevent portion of the file below). The problem is that the initial dial command does not execute properly in trixbox. I am hoping somebody who

thank you for your response below the asterisk -vvvr Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Executing [0176XXXXXX at from-internal:1] Macro("SIP/300-00000192", "user-callerid,LIMIT,EXTERNAL,") in new stack -- Executing [s at macro-user-callerid:1] Set("SIP/300-00000192", "TOUCH_MONITOR=1427481319.470") in new stack --

I am trying to find a way to allow dialout from voicemail when connected from an 'internal' extension context, but prevent dialout when connected from an 'external' extension context. As far as I can tell the dialout context that can be set in voicemail has no regard for the context from which the call to voicemail came in. Any ideas on this? Maybe a variable passed when

I've been reading the Linejack strikes again messages, and have another Newbie question is it possible to use a Voip Product as a Dialout line for * ? I have a Vegastream 100 Voip to PRI. box. With * can I use that as a Dialout / dialin box? The Vega100 does either sip or h.323. Thanks. Bradley Greep

Hi! I have an automated dialout via a call file to a mobile. Can I detect when the call is not answered but forwarded to the mobile operator voicebox? I would like to stop the dialout if this is the case. TIA, Mike

Hi, We are using VOIP-SIP gateway to route outbound PSTN calls. Recently, I am getting == No one is available to answer at this time message, after making 5 SIP attempts (Retransmitting #5 (no NAT):), and the calls are going out through alternate Zap-trunk. I do not see any hit (sip-debug traffic) on the voip-gateway for the failed calls. Strange thing is that this is happening randomly,

Larry Martell wrote: > On Fri, Oct 21, 2016 at 11:42 AM, <m.roth at 5-cent.us> wrote: >> Larry Martell wrote: >>> On Fri, Oct 21, 2016 at 11:21 AM, <m.roth at 5-cent.us> wrote: >>>> Larry Martell wrote: >>>>> We have 1 system ruining Centos7 that is the NFS server. There are 50 external machines that FTP files to this server fairly

Hi! I have configured a SIP trunk with a dialing rule. The trunk behaves normally for incoming calls but when in used for outgoing call a strange thing happens. When I place a call I cannot hear the tone confirming that the remote phone is ringing. I simply hear the voice as soon as the party picks up. When the remote phone start ringing Asterisk receives a SIP packet stating that the call is

Greetings, I am new to all this VoIP stuff and have been having a bit of a hard time getting my soft phone working as a SIP client thru Asterisk. I apologize to start off with such a simple question and hope it's ok to post this and see what others have done. THE GOOD NEWS: I have successfully setup Asterisk 1.07 on an OSX machine. The build is running and working successfully. I am able