similar to: asterisk strips off trailing digit from incoming calls

Hi all, On an Asterisk/Zaptel 1.4 system, one way to gather diagnostic info is: ~# cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC2 "HFC-S PCI A Zaptel Driver card 1 [TE]" AMI/CCS 4 ZTHFC2/0/1 Clear 5 ZTHFC2/0/2

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hi list, After upgrading from Asterisk v1.2 to v1.4.14, all kinds Zaptel error messages related to my HFC-S PCI card disappeared, but now I can't access the card's resources because it always seems to be busy. Any idea why? Thanks, Jaap PS -- Below is some info regarding my configuration. =========================== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Steve, 1) go to /etc/asterisk 2) open modules.conf for editing using vi 3) add this line: noload=pbx_wilcalu.so 4) Save the file 5) Restart asterisk Lightup the candles, open the Cabernet Savignon ( or whatever your prefernce) and call your girlfriend. ;) Seshu -----Original Message----- From: asterisk-users-bounces@lists.digium.com

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hello, I have about 10 Asterisk PBX in production with Bristuff-0.2.0-RC8q (asterisk 1.0.10) and I want to use Bristuff-0.3 now for the new PBX I am going to set up. With Bristuff-0.2.0-RC8q the ISDN lines are working fine, but the new version of Asterisk add some nice features. All these PBX are in France with France Telecom lines. When I use the new version after about an hour with

We have a machine with a TE410P in it acting as a client to route calls via iax2 to our central server, caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called client server often the called can't hear the caller (both machines on public ip) 'iax2 show netstats" on client machine shows more and more dropped packets on the

Hi :) I've had all this working before, but I'm revisiting it, and in short, I currently have huge problems receiving incoming calls. I've been trying with both FWD and voiptalk.org. I'm running CVS HEAD of asterisk, zaptel and libpri as of yesterday afternoon. Would someone mind helping? :) My machine is 10.0.0.1 on my LAN, but the ADSL router has 10.0.0.1 set as the 'DMZ

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

This is my musiconhold.conf and my folder: root@voip:/etc/asterisk# less musiconhold.conf [classes] default => quietmp3:/var/lib/asterisk/mohmp3 ;loud => mp3:/var/lib/asterisk/mohmp3 ;random => mp3:/var/lib/asterisk/mohmp3,-z ;unbuffered => mp3nb:/var/lib/asterisk/mohmp3 ;quietunbuf => quietmp3nb:/var/lib/asterisk/mohmp3 ; Note that the custom mode cannot handle escaped parameters

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A: