similar to: chan_unicall and /dev/zap/channel

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall libmfcr2-0.0.3 is

Dear HO SIN, many thanks for "L" solution you give me... I have also libtiff troubles with RH9, how did you resolve them ? R2 protocol I use work only with AB bits(CDbits ares fixed) and it run perfectely with the testcall.c, i'll try with chan_unicall and i'll give you the result... *** GOOD luck Steve for updating the patch of last asterisk *** thank you for your help

>any feedback would be awsome, the idea is to fill in the 30 channels of >the E1 all at the same time and see how stable it can be > > ----- Original Message ----- > From: "Miguel Cavazos" <miguel@cavazos.com.mx> > To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" > <asterisk-users@lists.digium.com> > Sent: Wednesday,

Hi, I have installed chan_unicall for MFCR2 on Asterisk 1.0.7, 1.0.5 and 1.0.4. - 1.0.7 does not send dtmf properly through unicall channels from sip snom phones on any mode (rfc2833, info, inband) - 1.0.5 and 1.0.4 are able to send correctly the dtmf tones when configured to INFO in sip.conf. Could this be a problem inside 1.0.7 when paired with libunicall ? Either version I am using, the

I am in the middle of installing chan_unicall.c and channels_Makefile.patch in my channels directory as instructed at the bottom of this doc/site: http://soft-switch.org/unicall/installing-mfcr2.html. I am at lost 'coz I don't know where is my channel directory is 'til someone told me that it is where all my chan_xx.so resides, so I copied them to this directory. Next, I have to issue

I have a problem with inbound and outbound calls in asterisk. I read previous thread, and then test new versions of unicall, but I don't have success, the problem persist. The system suffers CPU peeks with a single conversation, with an interval of 5 or 10 seconds. My system has: asterisk 1.0.5 zaptel 1.0.4 libunicall 0.0.3-pre3 hardware: E100P Also, I made traces with strace, but all

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in

Hi Kaws, I may need to add some notes; 1. The default .rpm version of libtiff in RH9 does not seem to contain some functional entries required for libunicall / libmfcr2. Therefore when compiling libunicall "unresolved references....." will happen. To solve this, I needed to recompile libtiff from the tarball. When installing libtiff, the default directories will be under

Hi, I have successfully installed libunicall and mfcr2 in Venezuelan variant. We are able to receive, make calls without any problems. When we place a call from a snom sip phone through chan_unicall and press a dtmf (either using info, rfc2833 or inband) Asterisk seems to get the order of playing dtmf but a garbage is heard at the other side. I have been trying to narrow down the problem on

Hi guys, I have one E1 with 30 channels in Mexico City, I guess that if i can fill this 30 channels with REAL traffic for 2 or 3 days I can find new bugs on chan_unicall or I can see how stable it can be. Im using R2/MFC with chan_unicall the patch that Steve Underwood wrote. I will let anyone make FREE LOCAL calls to Mexico City till saturday or maybe until monday to see how stable this can

Hi- I'm at my wit's end trying to get a Grandstream BT-101 POS to register on my * server. Asterisk version is 1.2.1. GS Firmware is rev 1.0.6.7. Basically, I've setup the phone following the instructions at voip-info.org, and it registers for about 10 seconds, then after receiving the SIP NOTIFY from the * server, goes into "flashing display" mode, which indicates some

hi all i have a TE110P connected to my PBX when i try to call a extension number in other location 3525 the asterisk give me a error -- User entered '3525' -- Executing [450 at lacnicuy:4] GotoIf("Zap/31-1", "0?6:5") in new stack -- Goto (lacnicuy,450,5) -- Executing [450 at lacnicuy:5] Dial("Zap/31-1", "IAX2/lacnic:splacnic at

hallo, I have a problem configuring lmtp service. I use postfix+dovcot2.0.7 with "recipient_delimeter = -". If i switch to dovecot-lda, all works fine, but going to lmtp service it dosn't. Maybe it works with default delimeter "+", but i plan to move from qmail system with many existent mailboxes. Enclosed some configuration/logentries. Can you give me a hint ? Best

On 2017-05-02 17:15, Luciano Mannucci wrote: > I have a problem with a physical user that was removed and recreated > whith same name and different uid. The home dir, the mailbox file and > the index directory where removed and recreated with the new uid/gid. > > I can feed the mailbox via procmail, though dovecot-lda complains that > userids do not match: > > May 02

Please help me to produce smoothed contour plots. I have dependent data generated at regular intervals of two independent variables and would like to produce smoothed contour plots - I cannot get interp (alima) to produce cubic interpolations of the data, only linear ones. I'm interested in smoothing as the data generation process is stochastic and produces small variations which I'd

Hello! I'm looking for an easy way to filter data frames. Some rows in my data frame needs to be left out, for instance, rows with invalid data. Right now, if I want to pair two columns of this data frame, I have to do this: > pairs(as.data.frame(list(tstart=df$tstart[valid],tend=df$tend.sdr[valid]))) or this: >

Hi, I'm having problems accessing home directories though NFS. This setup uses LDAP and Kerberos. Users defined on the local host work fine. This is what dovecot writes in the logs while trying to log in as the user johndoe: ---- Mar 19 14:10:54 jack dovecot-auth: nss_ldap: reconnecting to LDAP server... Mar 19 14:10:54 jack dovecot-auth: nss_ldap: reconnected to LDAP server after 1

Hi Christian, my english is very bad excuseme for that. I see that you resolve the problem describe more ahead, how compile dovecot?, can you send by mail the binary? Thanks Saludos RMZ Icesa - Orve S. A. 2261000 ext 307 Sitio de inter?s para Linux: www.openecuador.com [Dovecot] chdir() on NFS Christian Andersen

Head of Department of Applied Statistics and Epidemiology - Institute of Cancer Epidemiology, Copenhagen, Denmark The Institute Population-based cancer research in the Nordic countries is in the international forefront. Since the foundation of the Danish Cancer Registry in 1942 the Institute of Cancer Epidemiology has played a significant role in this research area. The Institute is looking

Hai, A quick reply. As far i can tell, the steps you did are fine. The only diffence here compaired to my setup. And i also use(d) an HP CP 3525, i used the PCL6 6.0.0 and 6.2.1 and 6.5.0 drivers. Off these i know they should work. Only thing here is i cant really the exact setup, its years old already and i changed to kyocera printers. One major thing here, i configured this all from a