similar to: Re: Asterisk-Users Digest, Vol 11, Issue 68

Hello All I'm settup my asterisk as belows: sangoma card, connected with E1, CAS Signalling. I have two problem. 1. The asterisk don't received any DTMF when caller input to 2. when i dial to system, the caller hear bad sounds. monitor on console. asterisk show error. Jun 11 12:15:45 WARNING[1496]: channel.c:1447 ast_read: Exception flag set on 'UniCall/6-1', but no exception

Hi When I make a call from the outside to asterisk and the call is asnwered, all is OK, but when I make a call from the outside to asterisk and hangup before the call is answered, you got this WARNING in the console: Jul 6 19:33:08 WARNING[10037]: channel.c:1521 ast_read: Exception flag set on 'UniCall/2-1', but no exception handler Jul 6 19:33:08 WARNING[10037]: channel.c:1521

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Hi All i used cangoma card, connected with E1, using unicall. asterisk 1.1.x. when i dial to asterisk server. asterisk show error as belows: -- Unicall/9 extension '9' in context 'from-pstn' from '71811242' does not exist. Rejecting call Jun 10 16:47:59 WARNING[28159]: chan_unicall.c:2655 handle_uc_event: Unicall/9 event Far end disconnected Jun 10 16:47:59

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Hi all. When I place a call Im getting this error: Jul 25 09:50:07 WARNING[3200] channel.c: Exception flag set on 'UniCall/13-1', but no exception handler Lots of this messages appeared on my Asterisk full log and the CPU got 100%. Topology: Analog Phone - Hicom300H E1 - E1 Asterisk - IP Trunk Problem: 1. Calls from Analog Phone through Asterisk is ok, but the messages appeared.

Hi All, I have installed chan_unicall and MFC/R2 successfully, and is runnign fine. But I noticed that once unicall is installed, asterisk CPU usage as reported by 'top', jumps to 99% every few seconds. I have no incoming calls, and I have even removed the E1 lines from card and I tried almost everything possible but I was not successful in determining the cause of this high cpu

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Hi, Please advice how to download utility for 'tar', 'cp' supporting RHAS3.0 RPMs listed in note 237997.1 are used for RHAS2.1 * Patch 2883583: fileutils-4.1-4.2.i386.rpm * Patch 2913284: tar-1.13.25-9.i386.rpm Best regards, Huy. == Nguyen Quang Huy Sr. Technical Sales Consultant Oracle Vietnam 53 Quang Trung St, Hanoi Email: quang.huy.nguyen@oracle.com Phone: +84 4 943 2595

Hello All I need to use Asterisk with an E1 sangoma card with CAS R2 signalling for Vietnam what is difference between libr2 of CVS and libmfc2 of soft-switch.org ? how to compile chan_unicall.c on asterisk. asterisk update CVS-head- May 27 2005. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

When OCFS2 is available as Production? == Nguyen Quang Huy Sr. Technical Sales Consultant Oracle Vietnam 53 Quang Trung St, Hanoi Email: quang.huy.nguyen@oracle.com Phone: +84 4 943 2595 Fax: +84 4 943 2592 == -----Original Message----- From: ocfs-users-bounces@oss.oracle.com [mailto:ocfs-users-bounces@oss.oracle.com]On Behalf Of ocfs-users-request@oss.oracle.com Sent: Tuesday, May 24, 2005

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

Hi, executing the reload command on Asterisk make the Unicall channel unblock all Unicall channels dropping active calls. Is this just a local error (maybe in the other end of my E1 ?), an option in the source (maybe a debugging option ?) or it must be this way ? Asterisk: 1.0.9 unicall: 0.0.3-pre4 protocolvariant: br Thanks, Leonardo Aug 31 15:00:55 WARNING[28411]: Already have a

Hi, ? I run the program testcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Hi list: I want to modify the libmfcr2. But i can't find where is define the end DNIS signal is define. Actually the libmfcr2 send a ONE (1) at the end of sending all the DNIS numbers. I need to send a TWO (2), this becouse in Mexico the normal is to send a 2 at the end, not a ONE. In the next example i dialed un 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Call control(1)

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or