similar to: Phantom incoming calls on x100p

I'm getting these "calls" at 16 and 46 minutes after every hour. The SIP phone rings, and if we pick up, we get a dial tone. If we don't pick up, we get the dial tone in a voicemail message. An analog phone connected to the incoming POTS line doesn't ring (whether or not * remains connected to the line). It's like the horror movie where the babysitter is getting

I have been experiencing hung up when answering incoming calls through x100p. NOTICE[1242768320]: chan_zap.c:4584 ss_thread: Got event 2 (ring/Answered).. -- Executing Wait("Zap/1-1","1") in new stack -- Executing Answer("Zap/1-1","") in new stack -- Executing DigitTimeout("Zap/1-1"."5") in new stack -- Set digit timeout to 5 --

About once a day I have noticed a phantom incoming call with a caller ID of asterisk@192.168..<cut off>. When I answer the call there is a dial tone and the call is disconnected. Any clues? David Koski david.nospham@kosmosisland.com

Hi, I connected my Wildcard X100P to the PSTN and created a context in extensions.conf which rings a number of SIP phones on inbound calls from the PSTN. When I compare the actual PSTN rings with Asterisk recognition of the incoming call, Asterisk rings my SIP phones on the third ring of the incoming call. Here is some log info: On the first ring: -- Starting simple switch on

Hi, I'm running Asterisk 1.0.8 on Gentoo, with an X100P (clone) card, and I'm having problems with Caller ID. I have run clidtest, and it seems happy enough, returning:- server clidtest # ./clidtest /dev/zap/1 Number: 0412222222, Name: MOBILE (that number's fake.) However, I'm not getting the caller ID passed through with *. Sometimes I get a "failed checksum" like

Hi, I'm running Asterisk 1.0.8 on Gentoo, with an X100P (clone) card, and I'm having problems with Caller ID. I have run clidtest, and it seems happy enough, returning:- server clidtest # ./clidtest /dev/zap/1 Number: 0412222222, Name: MOBILE (that number's fake.) However, I'm not getting the caller ID passed through with *. Sometimes I get a "failed checksum" like

(hardware in my computer: linux, asterisk, x100p, grandstream budge tone-100 ) Hi, When i run #asterisk ?v It show me a messages but when i try to incomming the call it show me that. Apr 11 07:59:01 NOTICE[81926]: chan_sip.c:3140 sip_reg_timeout: Registration for 'me@192.168.0.6' timed out, trying again Apr 11 07:59:01 NOTICE[81926]: chan_sip.c:5568 handle_request: Registration

Can anyone tell me what this message means? Got event 17 (Polarity Reversal)... I'm running DAHDI 2.0 with a TDM401 card. Asterisk version 1.6.0. It appears that I get this Polarity Reversal each time an inbound call hangs up. This results in another ring, but no one is there. It appears as an unknown caller, but I believe its a phantom. Thanks, Jim [Oct 10 12:47:54] NOTICE[6669]:

A very good day to you all, We can't get the phones to pick up on an incoming call on analog trunks. We're using the digium products in the box, with snom phones internally. This is the output from the asterisk console: linux*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo pstn-incoming en default 1 pstn-incoming

Using the latest SVN of zaptel and asterisk, I can no longer receive incoming analog calls. The caller just hears it ringing but Asterisk doesn't pick up. I am seeing these error messages: [Apr 9 09:38:02] WARNING[16564]: chan_zap.c:6470 ss_thread: CallerID returned with error on channel 'Zap/2-1' [Apr 9 09:38:50] WARNING[16570]: chan_zap.c:6470 ss_thread: CallerID

Yo! I changed callprogress to no, and in wcfxo.c source around line 334 i changed the value 32000 and -32000 to 10000 and -10000 because it had something to do with the DC voltage when it was ringing. I found reference here (http://www.voipuser.org/forum_topic_1791.html) with an interesting diagram of wiring that was incorrect for sending voltage to a phone or something like that. So put it

hi, when i call asterisk (on x100p) i got this : CLI> -- Starting simple switch on 'Zap/7-1' Jul 13 15:03:34 ERROR[311316]: callerid.c:192 callerid_feed: fsk_serie made mylen < 0 (-9) Jul 13 15:03:34 WARNING[311316]: chan_zap.c:4735 ss_thread: CallerID feed failed: Success Jul 13 15:03:34 WARNING[311316]: chan_zap.c:4777 ss_thread: CallerID returned with error on channel

I have an Asterisk server running todays CVS (updated it just in case that was the problem). It has 3 X100P cards. The first two lines I use as my normal work lines and the third is my fax line which I use with SpanDSP. I run Fedora Core 4. I have a problem that the third X100P does not answer the call. From the console I can see that there is an incoming call with the following: --

Hi Folks, Prior to upgrading my Zaptel sources everything was working fine. I have a X100P connected to my analogue line. The handset port of the X100P is connected to my desk phone's line 2 input. When the analogue line rings I see the CID on my line 2 but not from Asterisk on line 1 via the Cicso ATA. This used to work fine until I upgraded the sources. I get this when watching the

I'm getting this error on incoming calls on my X100P cards: -- Starting simple switch on 'Zap/1-1' Oct 7 15:49:19 ERROR[74769]: callerid.c:260 callerid_feed: fsk_serie made mylen < 0 (-2) Oct 7 15:49:19 WARNING[74769]: chan_zap.c:5369 ss_thread: CallerID feed failed: Success Oct 7 15:49:19 WARNING[74769]: chan_zap.c:5411 ss_thread: CallerID returned with error on channel

[root@www root]# cat /proc/zaptel/1 Span 1: WCFXO/0 "Wildcard X101P Board 1" 1 WCFXO/0/0 FXSKS (In use) Asterisk CVS-HEAD-02/13/05-00:32:03, Copyright (C) 1999 - 2005 Digium. Feb 15 22:33:48 NOTICE[3002]: callerid.c:307 callerid_feed: Caller*ID failed checksum Feb 15 22:33:51 ERROR[3002]: callerid.c:261 callerid_feed: fsk_serie made mylen < 0 (-6) Feb 15 22:33:51

I have a normal backup phone (and an alarm panel) sharing the POTS line with the Digium X101P FXO: | | Wall |>---+------X101P FXO as Zap/5 | | | Phone & Alarm Whenever the Phone is used, Asterisk sees a 'false ring' signal immediately when the phone is hung up. The Alarm panel dials out nightly at around 1AM, and each time it completes the call, Asterisk

Sorry if this is a daft question but when a PSTN call comes in on my X100P the console shows the following; NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2 (Ring/Answered)... NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2 (Ring/Answered)... NOTICE[1217602880]: File chan_zap.c, Line 4456 (ss_thread): Got event 2 (Ring/Answered)...

I've got a single phone line coming into an X100P. In extensions.conf I've got this: [inboundzap] exten => s,1,Answer exten => s,2,EAgi,hanguptest.agi I see the ring come in and Asterisk detects it and tries to do something with it: NOTICE[20492]: File chan_zap.c, Line 4017 (ss_thread): Got event 2 (Ring/Answered)... -- Executing Answer("Zap/1-1", "") in

Hi, I've got an x100P and I'm able to dial out and make phone calls with it ok but I just want to set it up to answer the phone and be a simple answering machine but it doesn't seem to want to answer the phone. I keep getting this: on the console when the phone rings: -- Starting simple switch on 'Zap/1-1' Nov 28 08:55:09 NOTICE[29298]: chan_zap.c:5458 ss_thread: Got