similar to: SIP Connection Timing Out BroadVoice

Hi, all. The asterisk setup is working fine, receiving calls via broadvoice "initially". ? When call comes in via broadvoice number, asterisk picks it up and routes correctly, as long as the call came in within ~2 min from the previous one. In other words, as long as a call comes in within ~2 min since the previous one, asterisk will answer the call. However, if the call comes in

Hi all, I just upgraded to Asterisk 1.4.18 a few days ago and I don't use Broadvoice TOO often, however I have a Vermont number with them and so my mother in law calls it to talk to my wife once in a while, so that's why it took me so long to notice it wasn't working. Anyway, when she calls she gets a busy signal (as I've tested when calling it from my cell). When I enable

Hello everyone, Well here is my initial posting to the list, and I will admit Asterisk is new to me. I just got everything running here a couple days ago, so still learning the ropes for sure. OK, here is my problem. Currently I have it setup talking to a couple Cisco IP phones, and some Xten softphones, this works great. I also got an account with FreeWorld Dialup using IAX2 and that

*sigh* Ok, I have fought and fought with this. I have read all the FAQ's, I have scanned the list archives. I can receive calls on * from my Broadvoice acct, but I cannot place calls... I have the 'World Unlimited' plan, and like 5 area codes that are local to me in Dallas. Can anyone help me? here are my config files... - sip.conf - [general] context=default ;

I'm looking to find a test tool that will register with our Asterisk (Trixbox) server here at work and place an outgoing call via our main SIP trunk (BroadVoice) to confirm that things are working. I've looked around but I can't seem to find any tools that will do what I'm looking for. I can't just monitor the status of the trunk inside Asterisk, as this is the normal status:

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

I've setup Asterisk to work with Broadvoice for both incoming and outgoing calls. I can make outgoing calls, but when I try to receive an incoming call I see the following message on the console: [date] NOTICE[8661]: chan_sip.c:13178 handle_request_invite: Unable to create/find SIP channel for this INVITE It's registered with Broadvoice: Name/username Host Dyn

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

I have an idea, tell me if this wouldn't work... I know it's really ugly, but it might help some people until we can get round robin DNS checks for peers... Since * does not do GetHostByName() again until you reload your config, and BroadVoice and I'm sure other sip providers are using round robin DNS, why not create 2 [<your server here>-out] contexts in sip.conf, and then in

I have just installed * from the latest CVS and I can make calls via X-Lite to outside numbers but for only 30 to 35 Seconds at a time then Broadvoice will hang up on me but X-Lite will not know it. Once I hang up X-Lite then I will get the following error message: Spawn extension (default, Number-I-Dialed, 1) exited non-zero on 'SIP/200-6a22' -- Got SIP response 404 "Not Found"

All, I signed up for a broadvoice BYOD plan over the weekend (very excited about their offering) and after about an hour I had asterisk registered and was making in and out bound calls. However, the next day (without changing anything) I couldn't call in or out and haven't been able to get it going again. I can connect using a softphone (X-Lite) and make calls in and out

Hello - I've been using Broadvoice with Asterisk for a couple of months with no issues. Today, it has stopped registering. The Sip Debug from CLI is below. It tries to register five times and then gives up. Any suggestions? As you might suspect, I have not been able to get Broadvoice on the phone and usually get cut off after being on hold about 5 minutes. Strategic portions of IP

I just signed up for the BroadVoice service a few hours ago, but for the life of me I can't get any incoming voice. The incoming connection is fine as it rings my extension from outside, but I can't hear anyone talking. Outgoing voice is working fine though. I've been looking through the archives, but I haven't found a solution to the problem yet. I even tried another router

I have configured asterisk with the AMP php configuration utility. I am able to make outgoing calls through broadvoice but incoming calls are sent to BV's Voicemail and never actually enter the IVR. When I show sip debug info through the asterisk prompt it actually reads the incoming call from BV but then issues a busy signal sending the call to BV's voicemail. I also modified

We have a basic application that runs a SIP channel to pick up a call and process it. We are using Broadvoice and it's been working great. We recently rebooted the machine and now when a call comes in Asterisk picks up the call but does not process it. Asterisk seems to send the call back to Broadvoice. Nothing at all has been changed in the configuration to warrant this. Below is the

I have been going crazy with this also since Sat. Our server was working perfectly with BV but will now not place calls to BV. Incoming from BV works fine. I felt sad rebooting it today, it had been running for almost 200 days! Here is my error message from the console... Notice I am running today's CVS Connected to Asterisk CVS-03/08/05-14:32:39 currently running on com (pid = 1624)

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

I'd be grateful if someone could point me in the right direction. I have a Broadvoice trunk attached to Asterisk which I use for frequent calls to the UK using the following in extensions.conf exten => _0[1-68].,1,Ringing exten => _0[1-68].,2,Dial(SIP/BV/01144${EXTEN:1}) exten => _0[1-68].,3,Hangup The caller hears immediate ringing, though it seems that Broadvoice

Hello All, I have one X100P card for inbound calls. I use two Broadvoice SIP accounts for all my outbound calls. I'm unable to place calls using BV. Inbound BV calls are ok. Verbosity is at least 3 -- Executing Macro("SIP/201-365c", "dialout-default|XXXXXXX") in new stack -- Executing GotoIf("SIP/201-365c", "1?4") in new stack -- Goto