similar to: Getting a Quintum AS200 to connect with Asterisk using SIP?

Hi All I'm trying with no luck to connected the Quintum D series Gateway with the new SIP release to asterisk. Have anyone done this? If yes then how should I configure the sip.conf to accept the registration? maybe a sample config? Thanks /Krystian

Hello, I got Quintum A800 with the P5-2-1 firmware. I configure my asterisk trunk as followed: [SIP_BD1] type=peer qualify=yes host=192.168.0.254 disallow=all context=from-pstn allow=h723 and inside the quantum I change the config sip useragent to 5060. Up to this part if I run sip show peers, I got: asterisk1*CLI> sip show peers Name/username????????????? Host??????????? Dyn Nat ACL

Hi, I have an asterisk and a quintum AFT200 with two FXO ports, and want to use it as a gateway to handle outgoing and incoming calls. I have found this thread, http://lists.digium.com/pipermail/asterisk-users/2005-February/084015.html But I think I need a little more help, could anyone knows where I can find the basic configuration for this quintum to get it connected to Asterisk using SIP, no

Hello, I try configuring Quintum DX gateway as link to PSTN for *. Now, I can dial number which is connect to Quintum, and call is diverted to *. I don't know what I should set, if I want call from SIP_phone registred in Asterisk to PSTN via Quitnum. I set in sip.conf account for Quintum [sip_proxy-out] type=peer outboundproxy=QUINTUM_IP , and changed extensions.conf. When

Hi, I'm having problems to register Quintum Tenor DX 3020 on a Asterisk box with SIP. Asterisk always returns "Username/Password mismatch". I've tried all configurations that was on the Quintum's manual, but no success. I've tested the same username and password with a Linksys (PAP2-NA) with the same asterisk box, and it worked fine. Where is the problem ?

Hi all, Can someone share with me his experience in making asterisk-oh323 talk to quintum gateway without gatekeeper. My set up is QUINTUM GATEWAY ------IP----M ASTERISK (OH323) Both are gateways.. but I don't know what authentication I will set up in oh323.conf and how to set it up I will be glad if anyone can help Goksie

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio i have scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for interanet no PSTN at all just only IPphones and analog phones connected on FXS port.Is it's neccassary to cannect with

Hello, My colleague installed a Asterisk home as company's SIP server and I would like to integrate the Quintum gateway (SIP) but the calls don't get through. Bellow is are the configurations on each side: Quintum ******** Primary Registrar = 202.69.190.244:5060 Primary Registrar User Name= sipquintum Primary Registrar Pwd= sipquintum Primary Proxy =

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio? i have a scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for intranet no PSTN at all just only IPphones connected through ehternet port and analog phones connected on FXS port.Is

Hi All, Is it possible to use Quintum AFT800 on Asterisk 1.4.29 as Trunk for Analog (like Digium Analog Card) ? And if it's possible, could any one please give me the reference how to configure it on Asterisk 1.4.29. Thanks Regards, Zoel Hairi -------------- next part -------------- An HTML attachment was scrubbed... URL:

Well the subject line probably says it all. I have a Quintum D3000 which I'm supposed to be getting connected up to our Asterisk system. No matter what I try, neither username or authuser config works. I've also tried md5auth and it still refuses to register. Any one have a config they could share with me? Any help would be much appreciated. Neil

Please has anyone on this list had experience with getting Quintum equipment to talk to Asterisk? Specifically a D3000 in my case. It is refusing to register and I'm out of ideas. Any help appreciated. Neil

Hi, just wondering if there is anyone that can help me configure my quintum box to operate with asterisk. i have tried and made numerous attemtps configuring the tenor to work with asterisk@home but have been unlucky. anyone out there has a cheat sheet to configure this device. thanks.. for some reason i cannot get it to work. your help is appreciated.

Hi. I'm trying to configurate Quintum AX to work with Asterisk SIP egister/Proxy server and my problem is that only the first user account get logged in and only that user is able to make call correctly. It seems to be a problem with authorization - I have noticed no "Proxy-Authorization" information in SIP INVITE, ACK, CANCEL messages. I have also noticed that when I remove

I just upgrade quintum A800 with new SIP firmware ---------- Product Name: Tenor Analog A800 Multipath Switch - 8 ports (Rev. B) Gatekeeper Status: Mini GK Calls Allowed: 8 Feature Bit Status: -PS/+RB/-ER Languages allowed: 1 Serial Number: A002-00308F Ethernet Address: 00-30-E1-00-30-8F IP Address: 10.101.0.10 Subnet Mask: 255.255.255.0 Default Gateway: 10.101.0.1 System Software Version:

My fellows, We have Asterisk@home installed and we want to interconnect it with our existing quintum gateways.. any idea how to config that? Your time is very much appreciated.. Cheers, Jessie -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050220/2518797c/attachment.htm

Let's try this again. I have a Quintum AX Tenor gateway sending calls to Asterisk from BT analogue lines connected to FXO. The agents hear an echo on their side but incoming callers hear the conversation fine. I can't seem to find the problem. Anyone seen this issue before? <p style="margin: 0; padding: 0; border-collapse: collapse; font-family: Tahoma, Arial, Sans-Serif;

Hi All, I have a weird problem. I have asterisk setup using the G729 Codec to receive Incoming calls both from a SIP Gateway (SER and Quintum) and via ISDN using i4l and have rules setup in extensions.conf for sending calls out either back via the SIP Gateway or ISDN. What I want to do is have PSTN calls come in via the SIP Gateway, be answered by the auto-attendant and then sent back out to

Is anyone using FreePBX in production level systems because I'm just wondering if its stable enough to use. Currently I'm editing my own *.conf scripts but it sure would be nice if there were some sort of web interface for other people to use. The only thing holding me back is the stability of the FreePBX package... Any comments on this? Thanks in advance. Regards, Min Chang

Hi Guys, Hope fully somebody out there will have experienced this and can shed some light on how it was overcome. Current setup includes asterisk 1.6.2.11, GNU GK and a Quintum Tenor CMS on the same lan. Earlier I was unable to make a sip call from the CMS back to a sip client registered on my asterisk box. So I moved onto passing the call from the Quintum CMS to a Quintum Tenore DX which is also