similar to: TDM400P strangeness

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

I recompiled Asterisk with the aggressive echo cancellation on. That's all I changed, honest. After recompiling, it refused to run. I tried updating the source, etc, and eventually went back to no echo cancellation. Every time, I got this error while starting Asterisk. Please help! I have no idea what went wrong. Oh, and yes, wcfxo and zaptel are loaded, I checked with lsmod. I

Hello, I am currently using MusicOnHold(mpg123), and it works just fine, but every once in a while I will get a flurry of warnings in the CLI like those below and Asterisk will freeze completely, and the only way to come out of it is with a kill -9 . Is mpg123 causing my problem? Is there a specific format of MP3 that should be used/avoided to not have errors like these? Any help would be greatly

Hi,all I am newer to Asterisk.My Asterisk version is the newest CVS-HEAD.now something appears in the console CLI like below these,I don't know what's happen to my Asterisk Server.Could anybody help me? Thanks Junk at the beginning Warning, flexibel rate not heavily tested! Junk at the beginning Warning, flexibel rate not heavily tested! Warning, flexibel rate not heavily tested!

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi all, I just upgraded asterisk from 1.0.7.dfsg.1-2 to 1.2.7.1.dfsg-2 on a debian system. As I go to restart now, I get this error and can't get asterisk started. [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found May 17 12:11:25 ERROR[13298]: chan_zap.c:7007 mkintf: Unable to get parameters May 17 12:11:25 ERROR[13298]:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Dear list, I am trying to learn how to use Zap-things in Asterisk. While loading Asterisk verbosely I get this error: [chan_zap.so]Warning, flexibel rate not heavily tested! => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Mar 12 17:19:01 WARNING[5563]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or directory Mar 12

Hello. Is this normal. Or does it mean there is a problem ? ------------------------- stop now Beginning asterisk shutdown.... Executing last minute cleanups == Destroying any remaining musiconhold processes Yuck! Error in buffer handling...: Connection reset by peer Yuck! Error in buffer handling...: Broken pipe Yuck! Error in buffer handling...: Broken pipe Asterisk cleanly ending (0).

Hi. I am having the following warning when using music on hold. It works from X-Lite to Grandstream. I get a lot of errors and warnings. 1.Warning, flexibel rate not heavily tested! 2. NOTICE[1100258240]: res_musiconhold.c:260 monmp3thread: Request to schedule in the past?!?! Thanks for any help. Full Output below: Jan 30 10:24:55 WARNING[1133718080]: chan_sip.c:486

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

I'm an asterisk newbie, so initially tried to install it on a Mandrake 10.1 (see config below) and with a bit of messing about using sample config, have been able to make the test call to device 1000, and also through to the IAX test number at Digium. However, operation is extremely flaky - I cannot reliably startup and use the system on a regular basis. I have several problems listed below

I just received two TDM400P cards, but I'm having problems with them. The full info is at: http://pastebin.com/824079 Extra, I'm using : libpri-1.2.3 zaptel-1.2.10 On a x86 stable Gentoo box. Kernel: 2.6.17 gcc-4.1.1, glibc-2.4-r4 Is that an hardware problem? Should I try the other card? -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog:

Hi ! :) Does someone have an idea of the reason why my MusicOnHold (with clean mp3 downloaded from http://aussievoip.com.au/wiki-MOH) is always having interruptions and micro-cuts ? No high load of the system, no swap, no hard disk r/w, mpg123 seems running well... nothing ! Except a little message at startup : "Warning, flexibel rate not heavily tested!" I'm getting

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS