similar to: Re: Asterisk-Users Digest, Vol 11, Issue 48

Hi, I'm using asterisk with chan_h323 together with gnugk. chan_h323 and gnugk were recently compiled with pwlib-1.5.2 and openh323-1.12.2 as advised. When connecting asterisk directly by ohphone (without gatekeeper), everthing is fine. When using gnugk for usage control in routed mode, I find a funny situation in asterisk's H.323 debug: == New H.323 Connection created. --

I've been banging my head on this one for a few days and am quite stuck. I've got a gatekeeper running and everything works there. Netmeeting works calling other netmeeting clients. Netmeeting calling asterisk connects, but netmeeting can't generate the signals to make the demo do anything other than talk. But connection from ohphone always disconnects straight away. I can't seem

Hi to all, I've installed Asterisk 1.4.9 with h323, and gnugk as soft gatekeeper. I've tested h323 using ohphone and I can talk between them, then I've tested SIP with Twinkle softphones and function very well. Now I have to perform call from h323 to sip and viceversa. How can I do it ???? I receive h323 call from a Cisco Voice GW to my Asterisk and this call have to go to a SIP phone:

Hello All Anybody had used ooH323 for asterisk i using ooH323-0.7.2 and asterisk CVS may 2005. OpenH323 1.17.1 and pwlib 1.9.0 and GNUGK 2.0.2 audio is very good, better than SIP and IAX, but i have problem. how to router call from openh323 to outside PSTN. my h323.conf setting ; Objective System's H323 Configuration example for tvcti ; ooh323c driver configuration ; ; [general]

Hi, I am working on a H.323 project which involves GnuGk and Asterisk My current goal is to provide IVR functionality for the H.323 users which register through GnuGk(eg. call credit information) I have successfully built a H.323 platform using GnuGk - it uses SQL accounting and authorisation. Now I am trying to integrate it with Asterisk in order to provide IVR functionality as I already

Greetings- As most of you who monitor this list know, I've been messing about with Asterisk -HEAD, Cisco Callmanager, and the nufone H323 channel driver here for some time- with pretty decent success. I'm hoping to cash in a chip here- I've run into something that is probably a very simple answer, yet not found a decent reference to resolve it. Scenario- -HEAD as of last week

Hello there I'm quite a newbie in the IP Telephony area. I'm playing a little around with a setup with one linux box with a e100 p card installed, which functions as an Asterisk gateway and a oh323 GK(Gnu Gatekeeper). I have two h323 phones, Welltech WellGate 1501 and 3502. So far I've managed to get the two IP phones and Asterisk connected to the GK. I can place calls from one

hi all I'm trying to setup a dlink dph-100h phone (actually a dph-100m but with the h.323 software) with asterisk and chan_h323. AFACS, the dph-100h software can only be configured to point to a gatekeeper. I know I don't need to do this, but it's a test before I setup my Symbol Netvision phones (I don't have an access point for them now). First, this is what I have, and what

Hi all! I am using ohphone (well, I am trying to) to make calls. I will make an H.323 - SIP Gateway but I don't understand the architecture of all this. What is the exact role of asterisk? It can be used as gateway, that I know, but what else can he do? Is it necessary to have ohphone to make calls or asterisk can also do that? So when the gateway it is going to be implemented how is it

Hi, i'm trying to setup Asterisk to work with GnuGK using the Openh323 channel driver. I have a Gatekeeper that gets H.323 calls from a Cisco GW. To this Gatekeeper I've registered some endpoints, Cisco ATA186, Snom 100, etc. Now i want send the numbers 083xxx into Asterisk. Easy, i'll just enter something like this into oh323.conf: gwprefix=083 And all my calls starting with 083

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

Hello folks. We are trying to interconnect an asterisk installation with a gnugk 2.0.5 installation to become able to use some H323 hardware that needs a gatekeeper (particulary an Ericsson WebSwitch 100). We have managed asterisk to dial H323 endpoints successfully (although calls are interrupted immediately after connection with "spawn extension exited non-zero"), but we could not

Ok, I've managed to get inbound and outbound calling to work with chan_h323 and gnugk. A few questions: 1) if I do a reload in *, chan_h323 loses its registration with gnugk, and will no longer pass calls to it. A second reload will crash *. Is this supposed to be? 2) For a configuration in h323.conf like: [office] type=h323 prefix=9 context=outbound I get a message saying:

After much reading and fiddling - I have the gnugk GateKeeper running and can make calls from the H323 phone to the sip phone. Voice works bi-directionally.. Calling from SIP to H323 gives me a problem... Both gnuGK and Asterisk are on the same box. Someone said this was OK. Others said No. I added a second IP (eth0:1) and told gnuGK that was HOME. How do I lock asterisk to the other (eth0) IP -

Hi friends Can you please say me "How to send an extension number from ohphone to astersisk". For eg I have an extension 5454 at the asterisk. How can I make a call to that extension from ohphone. I tried with the command ohphone 5454@IPAddressOfAsterisk. But I could n't call that number. I want to do it without using any gatekeeper. Can you please suggest me the solution?

hi IIRC, Jeremy once said that chan_h323 could be used as a gatekeeper but perhaps lacking a few features as compared to gnugk. Is this possible? I have some dlink DPH-100H phoes here for testing, but they require a gatekeeper, and if I can do it, I'd love to keep gnugk out of this. thanks roy

hi, we are using a voip h323 switch. the switch sends all caals to our Gatekeeper (gnugk). gnugk musst send all calls to asterisk and asterisk must do his choice (sip endpoint or out to PSTN) Making calls to our h323 switch works fine over asterisk. what must i configure to get inboung h323 calls from our gnugk to asterisk? any hints for me? thx -- Thomas K?pper 01063 Telecom GmbH &

Hello everybody, First time installer and I need the lists advice. My plan is to use asterisk PBX with some hardware to terminate my calls coming from several operational gnugk gatekeepers. Do have RH9 and downloaded the latest asterisk from CVS. Compiled according instructions and is running fine. Could hardly find any info on h323 implementation untill the REAME in the channels directory.

Hi, I use with asterisk gnugk a gatekeeper for h323 client. I don't understand why asterisk can't have the H323-ID (callerID). In the gatekeeper's monitor I have this H323-ID but not in asterisk. Does anyone know something about it, or how can I send a caller ID to asterisk ? Rattana -------------- next part -------------- An HTML attachment was scrubbed... URL:

Current setup: Polycom IP3000 <-> gnugk <-> asterisk <-> Cisco 7940 Asterisk and gnugk are on 10.20.98.6 IP3000 is H.323, using G.711 (10.20.98.2) 7940 is SIP, using g711ulaw (10.20.98.3) I've been asterisk for a while now, only using SIP devices. I'm happy with that side of things, but I've not used H.323 before this week, in trying to get the IP3000 to work. *