similar to: Sipura 3000 dialing "noise"

Ok here is another problem I have run into. I have a Sipura 2000 and I have been able to configure line 1 with only one small problem. But I can't get the line 2 working with asterisk. Here are samples of my sip.conf and extensions.conf. If I disable line 1 I can then get line 2 working. Is there a sample configuration for the Sipura to get both ports working with Asterisk. Sip.conf

Does any body know if it is possible to group SIP channels just like it is possible with Zap channels? I have a group of FXO gateways (Sipura 3000's) and I would like to treat them as a group the same as I would Zap channels. Does anyone know if this is this possible?

Problem 1 - Outgoing: I am able to call out of the * box using the analog line attached to the sipura 3000 but when the person being called answers there is no audio from either end. * registers that the call was answered but passes no audio. Problem 2 - Incoming: When calling into the 3000 attached to * it never seems to pickup the line. The phones don't ring on the asterisk side. I used

Hi all, Anyone able to remotely reboot their password protected Sipura SPA-3000 from command line. I am trying: Sipura SPA-3000 from command line: # wget http://admin:mypassword@192.168.1.55/admin/reboot The strange thing is it works fine when I go to http://admin:mypassword@192.168.1.55/admin/reboot with my web browser... Thanks....

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

I have a couple of devices that need an analog modem to communicate outside of our Asterisk system. Most FXS gateways don't seem to support this... I have a stack of Sipura 2002's that are, AFAIK, worthless for this purpose. I've heard that Digium's IAXy FXS will work with modems, but I can't find any reference to that in their documentation. There is also the

I have installed two Sipura 3000's on my office pbx as a test, they work well an have some great features including fax detect, but I was hoping to allow incoming faxes on the FXO port to be detected and passed through to the FXS port. Am I mistaken or does this work, and how? Chris Mason Anguilla

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

Hello list, I have several SPA-2000's and 3000's scattered about the Internet (all behind NATs). Because I do not qualify as an ITSP, Sipura will not license their "Sipura Profile Compiler" so that I can have the units remote upgrade, remote re-configure, etc (via TFTP or HTTP). This is extremely annoying. Right now if I have to make a config change to any of these

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

The party's over folks, the new official cisco/linksys/sipura policy is to no longer sell SPA-3000's to end users. Buy them while you still can :-( -Dan

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

I would like the ability for a sipura sip device to instantly connect to an asterisk server as soon as the sipura sip device goes offhook and before any digits are pressed. This way asterisk can provide the dialtone and the dialplan. This also allows me to play a greeting to the phone before giving them a dialtone. Is there any way to do this, like possibly having the sipura device dial a

Dear list, I am playing with Sipura 3000 since last week. Through the wiki pages I could get running it reasonably well. My setup is that of a Sipura, linked with a local analog cordless phone, a local PSTN line and the setup to link to an asterisk server located at a remote static ip address. I can dial the cordless phone from other extensions located at the asterisk server; I can dial out

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

How can I dial *67 on a Sipura 3000 if I dial from a SIP phone connected on an asterisk server. I always get a message saying that authentication failed for INVITE for sip221@192.168.1.6. If I dial a number without doing *67 it's working fine... sip 221 being the extension of my Cisco phone and 192.168.1.6 being the IP of my asterisk server... I have my outgoing context configure

All- I'm attempting to set up a Sipura SPA-3000 in Sao Paolo, Brazil. Not being a portuguese speaker, I'm having a rough time of finding the relevant information on how to make the thing pick up the PSTN line and make an outbound call. The sipura in question works fine on a bench connected to a POTS line in the US, but is now plugged in in Sao Paolo. The immediate thing I notice is that

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike