similar to: DVG-1120S does not show callerid Name and resets time

Hi, I am having problems with callerid name and the time with my dvg-1120S. Every time I receive a call, it reverts the phone to January 1st 12:00am. I've looked everywhere in the browser and telnet configuration to change this. Also, it never shows the name of the caller. I've even tried forcing the caller id info using SetCallerID, but it still doesn't show the name. Any

So, I recently acquired an old DVG-1120M that was previously used with AT&T CallVantage service. It currently uses MGCP. I see online that there is a SIP version out there (DVG-1120S), which is essentially a DVG-1120M reflashed with the SIP firmware and the 'M' scraped off in favor of an 'S'. I've also seen people on this list saying that they flashed their M with S

I friend gave me his DVG-1120s after he realized that AT&Ts callVantage stuff would not work for him. It appears to be running a SIP version of firmware, however, it downloads an XML configuration file via SSL from AT&T. I cannot find a way to manually configure the VOIP portion of the unit via the GUI. I contacted D-Link to get an example configuration file so I could get it working

Hi, I have a dlink dvg-1120M (mgcp) box that i will like to use with asterisk. Is it possible? has anyone done that? Here's a link to the product page at dlink. http://support.dlink.com/products/view.asp?productid=DVG%2D1120M Also, does anyone has or know where to get the firmware for Dlink DVG-1120S (sip model)? thanks. -- Zahid

I upgraded a DVG-1120M to a DVG-1120S. Everything works great, but I'm having some caller ID issues on incoming calls sent to the SIP device. Using debug on the device, the caller ID looks fine - just as I set it in Asterisk. However, the phone is showing "CID TRANSMISSION ERROR". Should I check the RX and TX gain levels? Try another phone? Any ideas would be much appreciated.

Thu, 06 May 2004 12:31:33 -0500 there was an e-mail to the list from Isaac McDonald suggesting to re-flash the DVG-1120M gateway with the DVG-1120S code to have the gateway login to *. I have been looking and can seem to find the flash code. D-Link tech support doesn't know much about the box. Any sources for the TFTP file would be appreciated. Once this is running SIP will I need the xml

I had just found a Dlink DVG-1120 on ebay and I'm curious if anyone has used you it with asterisk. They were only $65. I have tested with the Linksys Pap2 and found that box to be fairly nice except for a lot of backgound/white noise. I was wondering if any else had experienced that? Let me know if I've wasted $65 on the Dlink and also if you had similar experience with white noise on

Hi all, I want to link three incoming Bell Canada centrex pstn lines (which currently go to an old norstar pbx) into asterisk. Can anyone suggest the most "painless" (i.e., "just works") way to do this? Has anyone used the D-link DVG-3004S four-port FXO-to-sip adapter, or the twice-as-costly Audiocode MP104-FXO-C3S? I know the Digium TDM400P or Sangoma A200 are options

Hello, I get warnings in my asterisk log: chan_sip.c:694 retrans_pkt: Maximum retries exceeded on call. I've used sip debugging to figure out the cause. It's my D-link DVG-1120S that don't understand message-summary events that asterisk sends out for MWI indication to the client. Is there any way to disable this in asterisk for this particular client? Tanks in advance, Magnus

We have extra equipment that was over-ordered or unused. All of the equipment is brand new. The equipment has been highly discounted to move quickly - the last set of equipment sold in 48 hours. If this equipment is of interest to you, call or e-mail quickly. Buy on VOXILLA and SAVE $300 each (Cisco routers & switches): http://store.voxilla.com/customer/home.php?cat=259 For Sale (all new):

Greetings all.. We have an inbound/outbound PRI installed and terminated on a T400P ? Digium Quad T1 card. We?re seeing an odd problem when sending $CALLERIDNUM when calls from the PRI are forwarded back out to the PSTN over the PRI. The $CALLERIDNUM is not being sent out along with the call. It?s sending the phone number of the PRI itself, rather than the $CALLERIDNUM information. Yes, we can

OpenSSH Unix Dev, Mac OS X 10.5 recently shipped with OpenSSH 4.5p1. This build includes a number of patches, some general bug fixes and some platform- specific fixes and enhancements. These patches are available from our open source site (http://www.opensource.apple.com/darwinsource/10.5/OpenSSH-87/ ). Following is a brief description of each patch. We'd be more than happy to

This is with an x100p (the motorola chipset) Two problems. Looks like CALLERIDNAME is being used uninitialized. On my other phones the callerid is fine and my buttset shows that the callerid passes the checksum. This is the relevant portion of extensions.conf exten => s,1,Answer exten => s,2,SetCallerID(H ${CALLERIDNAME} <${CALLERIDNUM}>) exten => s,2,Dial(${MGCP_ALL}) Here is

Does anyone have any experience using this DLink quad FXO <> SIP gateway with Asterisk? I'm still looking for an analog interface that I can live with, having tried X101p, SPA-3000 and TDM400...all with less than desirable results. Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power

Hello, Does anyone know how to set the outgoing CallerID properly when using Snom200/SIP/CAPI/BRI? Following doesn?t work: exten => _0.,1,SetCallerID,526910 exten => _0.,2,Dial,CAPI/526980:${EXTEN:1} Asterisk writes: *CLI> -- Executing SetCallerID("SIP/226-ada0", "526910") in new stack -- Executing Dial("SIP/226-ada0",

I'm having a problem with the callerID that the polycom IP600 phones are displaying. I would like to modify the CIDName and leave CIDNumber as exactly what the phone call came in as(provided they aren't hiding callerID). Most of the calls will be going to the queue, but a few will go directly to the SIP phones. I've done a various combinations of using SetCallerID(),

For outgoing calls made on our PRI circuit we are setting the Caller ID using the format Exten => _9XXXXXXX,1,SetCallerID(1601XXXXXXX) The monitor shows that the CallerID is being set to the specified number, but yet when the call is received on the user end the ID is always the base number of our DID. For example we have 8600-8650 as DID's but the callerid is always 8600 regardless of

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Is there any way to change the outgoing caller id on BroadVoice I have tried SetCallerID(Name <Number>) but that does not work Thanx -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050126/bbd95fcf/attachment.htm

I have an outgoing line that allows me to set my caller id. I want to be able to change the caller id when ever I place a call using this line. I would like my user to press 7, then be prompted for their 10 digit caller id number, then be prompted for the number they would like to call in the form 1NXXNXXXXXX. How can I accomplish this??? Right now I am using this script that users have to