similar to: Port 6057 blocked on firewall

I am using Cisco 7960 phones and have had a request to have the receptionist phone ring on multiple phones just in case she is not around. Call pickup is the theory here but the issue is that not all the people that need to hear the ring would here the receptionist phone ring so I think I need to have a second line appearance on the phones in question so that line will ring. Can this be done

I am trying to add a Polycom IP 3000 to our Asterisk system and am not getting anywhere. h323.conf [8908] type=friend host=192.168.104.25 secret=polycom context=crv-default callerid="Conference Room Polycom" extensions.conf exten => 8908,1,Dial(h323/polycom,20,Ttr) ; Polycom exten => 8908,2,Hangup I have tried setting the Asterisk system as both gatekeeper

I have encountered a frustrating problem with the meetme rooms and calls entering the system on the Digium analog cards. The typical scenario is: Callers on SIP phones, X-lite, Eyebeam, Cisco 7960, IAXy Callers entering the system from the PSTN via the digium Analog card (TDM400P) In the meetme room the SIP connections can all hear each other loud and clear. The PSTN people can hear

I am trying to find an ATA that will provice IAX2 and g729. I have not had much luck, I am hoping someone here might have some ideas. -- Scott Henderson ============================================================================ Finite Technologies Incorporated 3763 Image Drive, Anchorage, Alaska 99504 Phone: 907.339.8085 ext 6101, Fax: 907.333.4482 http://www.finite-tech.com

I have just finished setting up a new asterisk system which is basically the same as our first system. We are using 7960 phones and I used the phone config files the first installation with appropriate changes. The problem is that on the new system I get no message lights, I can't figure this out. One thing I do notice is that when I monitor the sip debug on the second system the sip

I have been trying to get multiple lines on the 7960 to work for several days. i have read all the posts I can find and have run multiple "sip debug" and have gotten no place on this. Here are the relevant section of the config files: sip.conf [scott] type=friend host=dynamic username=scott secret=scott context=default mailbox=6101 callerid=Scott Henderson [scott1] type=friend

I have set up an auto attendant and all is working but I am bothered by a long pause when switching between menus. This pause is between 5 and 7 seconds and is quite annoying. Is there anyway to address this. One other thing I find interesting is that when I move from the main menu to the sub menu the delay is there but when I move from the sub menu to the main menu the delay is not there.

I need to be able to dial a long distance provider that uses an access number and an auth code. I would like to be able to program this so that the user can dial 8 and then the long distance number, asterisk will hopefully do everything in the middle. The sequence to accessing the provider is on my traditional phone speed dial as: * Dial local access number * Wait 5 seconds * Dial the auth

I have Asterisk version 1.0-RC1 running on Debian Woody. I have 1 analog phone working, 2 inbound lines working, X-Lite is working. The problem that I am having is with Cisco 7960 with SIP version 7.2 software. I can make outbound calls and they work fine, I even get a notice that I have voice mail on the phone and it seems to register properly but I can seem to dial to the phone.

Here is the discovery that I have made. * I can Ping my phone w/o any problems. * Near as I can tell, I have set up the phone correctly in sip.conf * When I set up sip debug and/or sip debug ip and I reboot my phone, I do not see any activity from the server from my phone. Username Secret Accountcode Def.Context ACL NAT 1202 <password>

I am having a major dillema here, I have been trying to get my sip phone (hard phone) to communicate with the asterisk server. Below is my configuration: sip.conf [1201] type=friend username=1201 secret=<password> mailbox=1201 host=dynamic [1202] type=friend username=1202 secret=<password> mailbox=1202 host=dynamic extensions.conf exten => 1201,1,Dial(SIP/1201,9,rt) exten =>

I am looking for a SIP Soft Video phone, which I can use with Asterisk. If you have one installed (regardless if free or purchased) please tell me which one, the settings in Asterisk and your experience with it. bye Ronald

Hi all, I am using ftable and xtabs to get total counts of species per location per hight category (understory, midstory and overstory). i can save the data in almost the format i would like it to be - but not quite. Here it is an example of what i get: x - is a dataframe with the following columns: LocationID, Species, PercentCover, Category where Category tells if the Species belongs to

Hi all, I am using ftable and xtabs to get total counts of species per location per hight category (understory, midstory and overstory). i can save the data in almost the format i would like it to be - but not quite. Here it is an example of what i get: x - is a dataframe with the following columns: LocationID, Species, PercentCover, Categorywhere Category tells if the Species belongs to

I downloaded version 0.3.12 of TZInfo from [1], and observed that it has a very robust set of timezones including, for example, ''America/ Anchorage'': irb(main):001:0> require ''rubygems'' => false irb(main):002:0> require ''tzinfo'' => true irb(main):003:0> TZInfo::Timezone.get(''America/Anchorage'') =>

We are scheduling another meeting to discuss Theora matters. One of these was planned just a while ago, but it pretty much didn't happen. So let's make this one happen. Anyone interested in Theora or video technologies is welcome to attend. The place is #xiphmeet at irc.freenode.net, this Tuesday at 14:00 UTC. If you don't know when 14:00 UTC is, go here[1] for conversion into

We are scheduling another meeting to discuss Theora matters. One of these was planned just a while ago, but it pretty much didn't happen. So let's make this one happen. Anyone interested in Theora or video technologies is welcome to attend. The place is #xiphmeet at irc.freenode.net, this Tuesday at 14:00 UTC. If you don't know when 14:00 UTC is, go here[1] for conversion into

We are scheduling another meeting to discuss Theora matters. One of these was planned just a while ago, but it pretty much didn't happen. So let's make this one happen. Anyone interested in Theora or video technologies is welcome to attend. The place is #xiphmeet at irc.freenode.net, this Tuesday at 14:00 UTC. If you don't know when 14:00 UTC is, go here[1] for conversion into

Us folk who have been teaching ourselves Ruby on Rails development in the Columbia Maryland area are still meeting up each Monday to learn more about it. We''ve expanded the scope of our meetings to be more about learning ruby then just leanring about Rails itself. At this time we''ve got some people working on the rails project and other folks learning how to do Test Driven

To anyone who can help: I have two brief questions concerning sapply. Following below is the code for my example. The two problems are described at the end of the code: site <- rep(2:6, each = 12) tillage <- rep(c(1,-1), each = 6, times = 5) carbon <- c(18.23, 16.06, 17.81, 16.07, 17.26, 17.08, 14.92, 15.88, 12.11, 14.23, 16.99, 13.57, 20.34, 20.3,