similar to: ISDN data connection through Asterisk

I would just like to get a refresh of the situation for Australian users. It would seem that the TE400P is currently available and is likely to acheive approval for use in Australia within the next 2 months ? (when is the end of summer?). Once this is done, it will certainly suit larger installations, but it still leaves a number of 'gaps'. Anyone with analog phone lines will need

Using TDM400's here and I have tried everything to cure the echo. I have used the Milliwatt test from the telco and from asterisk to tune RX/TX gain via a patched ztmonitor. What happens is I experience midcall echo. I turned on aggressive_suppressor and it seems to do great. The problem happens with misc. noise around the office will cause it to mute the other end of a phone call while

I have recently installed Asterisk Now Beta 4 (32-bit) with three Digium cards - 2 Wildcards TE400P (one with 4 FXS modules and one with 4 FXO modules) and a TE205P dual E1/T1 card. The problem is with the TE205P and configuring the /etc/zaptel.conf and /etc/asterisk/zapata.conf files. I go in and add the required lines to configure the TE205P and restart Asterisk. All is fine until I reboot the

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

Hi! I have a E1 PRI connected to my TE400P card on span 1, and two channelbanks on span 3 and 4 and * 1.2. Every few hours I get this message and asterisk dies just after that: Warning: No D-channels available! Using Primary on channel 16 anyway! When this happens restarting zaptel and asterisk services, generally puts the system back online my zaptel.con reads: span=1,1,0,ccs,hdb3

Hi, I am just moving from Asterisk 1.2+bristuff up to 1.6.2, a huge leap :) I was wondering if someone could point me at 3 things that I appear to have "lost"? 1) ZapEC(off) - Is there an equivalent dialplan command to request no EC on a channel before dialling in DAHDI? 2) rxfax(file.tiff) - I have found ReceiveFax(), but I am aware that much has happened in the faxing stakes

Hello I've been having the following problem today : I have a quite simple dialplan made to receive a fax: [answer-extension] exten => 1,1,Answer exten => 1,2,Macro(setcallerid) exten => 1,3,Ringing exten => 1,4,Wait(3) exten => 1,5,Macro(stdfwd3iax-notransfer,${EXTENSION},${EXTENSION},$ {EXTENSION}) exten => fax,1,Goto(faxreceive,1,1) The Wait(3) is there simply to let

hi there, first of all: i am a newby concerning wine. the last reason to keep my windoze-partition is diablo2 and the t-online homebanking software (for all non-germans: t-online is germany's most common internet provider). since diablo2 seems to be a problem that can be solved, this leaves me with the homebanking software. does anyone have some hints for me whether running that stuff is

I have severe problems in calling my Netbank using Wine and Internet Explore, it do'nt work at all. My system is: RedHat 7.1, Windows 98 and Wine = codeweavers-wine 20010626 4. I can't open the login page of my netbank. Trying this IEX open an error page: res://C:\windows\system\shdoclc.dll/dnserror.htm saying: " .. The page you are looking for is currently unavailable. ... Check

Does anyone know of a way to simulate the signaling of a PRI trunk for testing/setup purposes? I realize this may be a rather naive question, but I was wondering if you could take a TE110, for example, and using a crossover cable (or not?) and some means of emulating the NI2 signaling protocol connect it to another TE110 on another machine to test and verify an installation before the telco

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Hi Folks I'm trying to run my homebanking-software under wine. How can I get networkaccess with wine ? I have already copied the winsock32.dll, but I think there has to be bone more but that ! Exists a FAQ for that problem ? -- Gru? Frank

Hi folks! My bank sent me a CD with the new version of it's Homebanking software. This new version uses internet for communication, the old one dialed with the modem direct to the banks computer. Because the old access will be revoked end of this year, it is very very important to switch to the new version. So I put the cd into the drive, mounted /cdrom an started "wine

I just wanted to see if any one else has seen this or could help point me in the right direction on this problem. I have a TE411P card in my * box. I am running FC4 x86_64. I used to have two TE110 cards in the same box that worked without any problems. Since changing to the TE411P cards, I am getting random DTMF tones being produced on a bridged connection through the same Channel Bank that I

Hey, I'm up and running fine with 30 Polycom 500s connected to Asterisk 1.2Beta on Cent OS 4.1 with a Digium TE110 connected to a PRI line. Nearly every hour, almost on the hour I get this: Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/1 successfully restarted on span 1 Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/2 successfully restarted on span 1 Sep 29

I have 4 guest VMs installed on 1 host. One of them is Vyatta (VC5). Currently we are using default Xen-bridge for communication between VMs(inter-domain or intra-domain). I want to assign Vyatta(a guest VM) exclusively to replace Xen-bridging for VM to VM communication. Means the traffic sent from guest-1 to guest-2 bypass briging and route through vyatta(VM), instead of going to Dom0. As

Hello, I'm talking about re-writing the classicupgrade HowTo since over a year now. :-) Now, after three rainy vacation days, it's finaly done: A complete and comprehensive re-write of the classicupgrade HowTo: https://wiki.samba.org/index.php/Samba_Classic_Upgrade_%28NT4-style_domain_to_AD%29 Some other mentionable documentation changes, I had done during the last week: *

I'm little bit confused which Digium hardware is certificated for use in Europe. It looks like new cards are certificated, like TE4XX series. What about TE110 or TDM400P? Can someone confirm that? Thanks, David -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060309/1d1c65a1/attachment.htm

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

I've got 2 internet connections but unfortunately not the same - 6mbit and 1 mbit. My default is 6mbit and I want to create backup connection (1mbit). How can do it? Has anybody done it? My perfect scenario is that my network uses 1mbit if (only) 6mbit fails and it switches automatically. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be