similar to: Can't make outgoing calls

Send Asterisk-Users mailing list submissions to asterisk-users@lists.digium.com To subscribe or unsubscribe via the World Wide Web, visit http://lists.digium.com/mailman/listinfo/asterisk-users or, via email, send a message with subject or body 'help' to asterisk-users-request@lists.digium.com You can reach the person managing the list at asterisk-users-owner@lists.digium.com

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

Hello, ------------- -------- --- -------- |Sip Softphone|-------|Internet|--------|F.W|-----|Asterisk| ------------- -------- --- -------- IP addresses: a.b.c.d q.w.e.r The SIP softphone(x-lite) is configured to register with the asterisk server through port 9090 (Domain q.w.e.r:9090).Firewall(F.W) is setup as the

Hi all, I have been worriyng and googling a lot but I can't find my mistake. I am trying to regiter an X-Lite Softphone to Asterisk, but I am getting a SIP/2.0 403 Forbidden response: SEND TIME: 10157385 SEND >> 10.100.249.12:5060 REGISTER sip:10.100.249.12 SIP/2.0 Via: SIP/2.0/UDP 10.100.249.86:5060;rport;branch=z9hG4bKFAC1B6F2B5414EE9855696A09A83FB22 From: Tester

Hello, they are successful to start asterisk, task that the error that I had previously had had to a configuration problem. Start asterisk in modality consol and when two softphone speaks is not felt well, and I have the following error: -- Registered SIP '1000' at 10.0.0.7 port 5060 expires 1800 -- Saved useragent "X-Lite release 1103m" for peer 1000 --

Apologies if this is a repeat: I trawled through the archives and couldn't find a reasonable answer, so I'm asking here. I have an Asterisk install connecting from behind a NAT device (DSL modem) to a SIP proxy (in my case, Broadvoice). I have an sjphone softphone on a Windows PC also behind the NAT device that connects to the Asterisk install, and using this setup I've been pretty

I have d/l the iso (*@home 0.9) , built the * box and followed the directions in the * handbook and http://www.geekgazette.com/index.php?option=com_content&task=view&id=2&Itemi d=26. I created extension 200 and verified that * was running fine. Loaded Xten lite, setup the proxy for local ip (10.0.0.201) per the handbook. After turning off the Norton Firewall protection, I am able to

Hello all, I am using a headset and the X-lite softphone (sometimes I use IAXComm, but I'm having difficulties using OSS emulation with it) to connect via uLaw to my internal Asterisk server, which is a Pentium II 400 with 128 megs of RAM. After getting this headset, most or all of the echo people on the other line were complaining about is now gone, according to them. However, every

Hello all, I've installed AAH 1.1 on my VIA C3 powered mini PC. I've made the necessary changes to the * makefile, so the compilation went well. The first thing I did was configuring two extensions from AMP, namely 200 and 201. Then I installed X-lite on two PC's and configured them with one of the extensions: System settings - SIP proxy - Default: Username: 200 Authorisation user:

I have a problem. Incoming calls work without problem but I cant call out. Using AAH.Gets a busy tone Anyone who can see a mistake in Outgoing settings context=from-pstn host=ipkund1.rixtelecom.se insecure=very nat=yes secret=xxxxxxxxxxx type=peer username=0406082250 Regards Anders Svensson -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello I have couple issues with AAH. 1.5 1. Flash panel doesn't show proper status. Sometime accessing with IP seems to work and it shows current line status etc. Sometimes accessing with hostname of the asterisk server seems to show lines, but it doesn't show off hook etc when we pickup a extension and talk. In /var/www/html/panel/op_server.cfg I have tried setting manager_host to all

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

hi, my asterisk has some problem when i call a destination number and the phone call is through a normal PBX... you can see from the trace that there is a "Forbidden" error... but i don't know why... someone could help? thanks, Angelo this is the trace: 9 headers, 0 lines Sip read: INVITE sip:00115601992@asterisk SIP/2.0 Via: SIP/2.0/UDP 10.8.210.147:5060 From: Giorgio

My question: How do I configure AAH via AMP to make a connection through our legacy PBX to the PSTN? Details: We're trying out Asterisk through Asterisk @ Home. Our legacy PBX has a modem type dial tone port that we hooked a Digium FXO to. Now I can dial from the XTEN client on my computer to any legacy PBX extension. If I connect a regular phone to the modem dial tone port, I can dial

Hi, I have two softphones connected to an Asterisk "stable". I have two extensions, say 1000 and 2000. When 1000 calls 2000, the call cannot be completed; the softphone (either Diax97a , SJphone, Firefly 1.8) on extension 2000 will ring, but as soon as the call is picked up, extension 2000 will hang up the call. The softphone on 1000 (SIP, SJphone, e.g.) will give a "403

I follow the advice of Alasdair, it was happening because of the multiple kernel panics. I have installed it again, and now it's working properly! Thanks a lot for your help. I'll change also all default passwords for security reasons. BR, //Laura From: "Steve Jones" <sjones@ftdata.com> Subject: RE: [Asterisk-Users] Asterisk@home default password doesn't match

Hi folks, I know this isn''t a shorewall question, but i''m hoping someone can point me to the right place to look for answers on this (since, as Tom suggests, search engines are useless for some things): Here is my firewall setup: ADSL1 ADSL2 dialup \ | / firewall | DMZ It''s a fairly simple setup. ADSL1 has a static IP, ADSL2 is

I'm in the initial stages of my asterisk experimentation, and after some messing about, have it working to some extent. Right now I'm in a pure SIP environment with no trunk lines and no NAT, and am configuring everything via Asterisk@Home. My problem is that I am only able to get one SIP device to be able to call out at a time. For example, if I register my Cisco 7960 at extension

Mateo, Dialing the extension to your softphone is the same as any hardware extension. Exten => 1000,1,Dial,(SIP/1000,20,trf) pretty exten => 1000,2,Macro(vmessage,1000) exten => 1000,3,Hangup Change [mateo01] to [1000] in your sip and you will be saying that ext. 1000 is registered with the specifics you are using. Update the settings in your softphone to register the name and

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>