similar to: Nearing my wits end....bad switch???

Has anybody experienced problems with a DSL modem stopping all other traffic when an IAX channel opens up? I've really traced this thing out as best I can - it isn't a lack of bandwidth on the DSL connection (I've had three concurrent Ulaw calls coming in at once with no problems), nor a problem within the network (other intranetwork traffic isn't affected by the call) - the

Hello all, We've discovered that VoIP (IAX2) + Citrix + Video is pegging the measly CPU on the Netopia router our ISP provided. We've got 3Mb/3Mb and will increase to 4/4 next year. The Netopia simply breaks out our WAN IPs, and we've got a switch hooked up to it on the inside (Actually I've got a QoS box in-between). ------------- | Internet | | on Cat5 | -------------

I am looking for a sample sip configuration of a SIP provider that runs Broadsoft VoIP switch. My sip provider is Conecta from Brasil, that only give me a SIP IP address to configure my asterisk box, when I call them for support or authentication data to load on my sip.conf, they say me that I don?t need such data, so, anyone knows how I would configure my Asterisk box against a Broadsoft peer?

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

I have a client with about 16 GXP-2000. They complain that the audio quality is terrible after 2 or 3 simultaneous conversations. They are behind DSL 1.5Mbps down and 256Kbps up. Because they are using G711.u codec, I know they upstream bandwidth is the limiting factor and they most likely won't be able to have more than 3 simultaneous conversations, and if they're surfing the

Greetings to all. I am not sure of this is a "user" question or a "business" so apologies in advance if it should be asked in the business list. A client of mine has a UK branch that is served by a provider that uses the Broadsoft solution. I want to create a sip trunk from a remote asterisk pbx to the client. The provider claims that Broadsoft has a strict

Symptom: Phone after about 15mins will stop functioning Problem: DHCP lease renewed but default route dropped Fix: Assign a static ip and problem is resolved. Upgrade to new firmware once it is released It turn's out that these phones have a few issue in 1.0.3.81 firmware. The phone may stop transmitting packets if configured with DHCP, if DHCP is being provided by certain devices. Netopia

I am using version 1.4.1.0040 and 2.6.1.0003. I have read about newer versions out there, how can I get them? I'm having an intermittent issue regarding DHCP with one of my phones, and I recall when I loaded 1.4.1 on this one phone, it failed once, then it succeeded the second time. I am wondering if a firmware update will help. Or is there any known issues with Fedora Core 2 dhcpd and IP

VPN (IP x.x.150.3) VPN (IP x.x.150.3) | | | | Cable Link DSL Link (IP y.y.y.y) (ppp0 z.z.z.z) | | | | Netopia R9100 Linux Router (IP x.x.125.1) (eth0 x.x.125.3) | | |

Hi, I'm considering setting up a small call centre, but I don't want operators to need to use their phone keypads. Supposedly, all required call functions (dialling, answering, transfer, on hold, hang up, etc), should be done via their scripts (be is a web interface, curses or whatnot) and not using either a regular phone, nor a gnome-phone type interface. Also, all this will be happen

Hi! They have in my university a Cisco VPN solution. Unfortunatelly, if you are cuban, irakian, iranian or a couple of other nationalities, you are not able to use it (sic...). I would like to study the possibility to install tinc as client. I've read that "There is no real distinction between a server and a client in tinc". Would tinc work as a client with the Cisco VPN? Of

I have one client that is telling me that their Polycom 500's format the file system every time they reboot, and also that they are unable to make changes locally on the phone itself, only via the config files. If the config file is not available when they try to boot the phone, then they receive an error about not being able to find the config file and then the phone will not boot up. Has

-------------------- ---------------------- | SDSL 1 | | SDSL 2 | -------------------- ---------------------- \ / eth1 \ / eth2 \ / *---*---*---*---*---*---* | Linux Router/Server |

Hi, I use shorewall-4.5.4 + lsm-0.143 and it does not seem to work as expected... When all providers are up, everything seems fine. When one goes down, lsm says "link <provider> down event"... and it seems ok but we then experience some problems such as a few unreachable sites, DNS problems... If I remove the downed provider from all confs and restart, everything works again.

On 11/04/2015 09:10 AM, Bowie Bailey wrote: > If all of the routers are providing access to the same network, you > can set up the same SSID, wifi password, and security type for all the > routers and the clients should seamlessly switch between them as they > move around. As a point of clarification: The setup that you're describing isn't multiple WiFi routers, it's

Hi, I have one satellite link and one sdsl link. And, one LAN link. My load balancing is working great with a iptables''s masquerading (no fw rules). Now, I need to route the following ports to my sdsl link: - 20, 21, 22, 25, 80, 110, 143, and 443 Whereas the others go to my satellite link. Does anyone done this before? Regards, rootlinux __________________________________ Do

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hi sorry for the slighty out of topic question but I''m sure someone here will be able to answer. Does anyone use some kind of remote connection to connect to MacOS ? I''m thinking of using VNC but I''d love to hear from other (especially secure) alternatives. I''m just fond of textmate, I have a dell laptop which I''d like to use as a terminal. kind

I'm having a problem with the callerID that the polycom IP600 phones are displaying. I would like to modify the CIDName and leave CIDNumber as exactly what the phone call came in as(provided they aren't hiding callerID). Most of the calls will be going to the queue, but a few will go directly to the SIP phones. I've done a various combinations of using SetCallerID(),

Hello List, in our office we have two independant SDSL-connections. One of them is a flatrate, the other is a dedicated line to our webfarm. The goal is to route all the traffic to the webfarm through the dedicated line and all other traffic through the flatrate. The maschine has three nics: eth0: internal network eth1: webfarm eth2: flatrate Each connection uses its own router. It is possible