similar to: Problem with calls on hold

Hello - I recently offloaded some of the SIP traffic on to a seperate Asterisk box and interconnected our main Asterisk system with the new system via IAX. The SIP clients are running 7960's. When a call is put on hold, often times when the call is pulled off hold, there seems to be no RTP in at least one direction. There seems to only be voice in one direction. Basically the call comes

Hi, this is the scenario: One * is placed in a central location with more than enough up/down bandwidth. One * is placed behind a DSL 3000/384. Both * are linked via IAX trunking. Everything is fine until the upload channel of the remote site is filled with a download, then heavy voice distortion starts. Well of course this is expected. So I fooled around with HFSC QoS scheduling on the remote

Two asterisk boxes 150 miles apart, both cvs-head as of this morning (and since Sept 27th), connected via iax2 with low-utilized ds3 internet, C7960 calls exten on remote system (also C7960), and call goes to VM. No other calls in either system (eg, no load). Both boxes have iax config'ed as: trunk=yes allow=ilbc jitterbuffer=yes Recorded VM messages are very distorted. Changing only

Good morning everybody, Can someone explain to me the interconnection between these four things: indications.conf, SetLanguage(), zaptel.conf and ring-back ? If there is any !! :- ) I am having this case where some users cannot hear ring back from a DeadAGI script and it seems to be interconnected to these items. These users are from the iaxfriends table, they _can_ hear ring-back from a

Hi All, At present calls over IAX2 (ilbc) are good but they suffer from occasional distortion. The strange thing is that the distortion can only be heard by the calling party and not the called party in 95% of cases. IAX2 is being used with trunking enabled, using the ztdummy module as a timing source. Bandwidth shouldn't be an issue as there is more than sufficient plus we use QoS

Hi all, I've setup two * servers which are SIP interconnected ala osaka/toronto from the * book (before anyone sugggests using IAX instead, no, I NEED to have them SIP interconnected for verification/test purposes). Then I have a Zoiper connected to one of them via IAX (so that * will not reinvite (?)). As soon as I try to call (via Zoiper) an extension on the other * I get a "Failed to

Hello Everyone, We are currently having talks with various service providers, and trying to determine what the best way is to interconnect in order to have access to the PSTN network. As you know there are two ways of doing this: Traditional PRI: Have trunks grouped into a transport layer such as OC3/12. With DIDs attached to the group. As you many know, this approach would also require a POP

Here's our config: cisco 7960's running 6.3 sip code latest cvs of * t100p zaptel card adit 600 channel bank 7 pots lines and 2 fax machines on the adit 600 dialing out from the cisco phones gets sent out via the zap channels, but I'm having some serious echo problems. I currently have the adit set to +3 rxgain and -6 txgain, with my zapata.conf containing: echocancel=128

On Samstag, 14. Januar 2006 1:47 tim panton wrote: > That is weird, you would expect IAX to do better than SIP (bandwidth > wise) My point exactly. > 1) are you sure IAX trunking is actually happening ? It shows (T) in iax2 show so I am pretty sure. Timestamps are enabled as well. > 2) what codecs are you using. Are the codecs the same for IAX as > for sip? G.711 alaw and

Hi I have 2 asterisk servers running 1.2.12.1 and IAX2 with trunking and no jitterbuffer. Both servers are using sccp2 with 7940's and 7960's with 7914. Server 1 is my main VOIP server and is connected to the pstn and VOIP wholesale provider. Sever 2 is a branch site and all calls go to server 1. If I make 1 call on server 2 everything is fine. If I make a 2nd call so there a two calls

Hi all, I'm trying to get IAX2 trunking between two * boxes and am having extreme difficulty :) What happens is when the sending * server (the one initiating the call) receives the ACCEPT back from the receiving server it immediately replies with INVAL. I've checked the code and it seems to be not matching the accept packet with the relevant item in the iaxs array due to the following

I've been having random problems when I make long distance calls using either VoicePulse or Nufone. Sometimes the calls go through clear, and other calls (or even just part of a call) the person on the other end just hears garbled voice, or really broken up voice. Sometimes it lasts for only a few seconds, but other times it goes on for a few minutes until I give up on the call. At

Hello, After checking out CVS HEAD from yesterday (for those new PLC/Jitterbuffer patches), I was affected by bug 3795 with my Polycom IP600's. After seing it resolved as of this morning (thanks Mark), I decided to try again... I can answer incoming calls. No problem there. Putting calls on hold, however, results in my Polycom IP600 indicating the call on hold, but the caller does

Hi all, I'm having a problem with some Asterisk servers interconnected with each other using IAX (I also tried with SIP without solving the problem) Sometimes, with apparently no reason, some peers become UNREACHABLE (I have qualify=yes in iax.conf) and REACHABLE again as soon as another qualify test is made. Our users are also complaining about audio loss during their calls, apparently

I've been having 'gappy' audio problems with nufone for about a week now but I think I've nailed it down. Setup: office* - iax2 - colo* - iax2 - nufone office* and colo* are identical physical hardware (Xeon 2.8, dual ethernet, solely used for Asterisk) -- they are joined together through their second ethernet ports over a dedicated 2meg SDSL link. One hop between office* and

I am trying to send calls from (telx-NY17S) to (telx-nyc) via an IAX2 channel. However the call is being rejected on the (telx-nyc) server. See error below copied from telx-nyc CLI> Apr 22 13:56:57 NOTICE[147465]: chan_iax2.c:5390 socket_read: Rejected connect attempt from 192.168.0.251 I have icluded the following conf files 1. extensions.conf (telx-nyc) 2. iax.conf (telx-nyc) 3.

Hi, I've had a hard time understanding what was going on in a new * setup. The deployment has a * box running on dual xeon RH9 stock 2.4.20-8 and some different versions of asterisk (1.2.10/1.2.16) + libpri + zaptel + wanpipe. Short version: audio from iaxclient clients is fine from windows but poor from linux when going to zaptel. E.g. Iaxcomm running on windows works fine, but the same

Two cvs-head asterisk boxes with iax2 working fine (without register statements). When two calls are placed simultanously from system A -> B and the packets are sniffed on the wire, I see the two calls using two different udp packets. At the top of iax.conf I have trunk=yes and jitterbuffer=yes (at both ends). I was expecting to see both calls handled within a single udp packet, but

Hello all, cell <-T1-> zap <-internet-very remote-> sip (ip430) The audio is choppy ONLY to cell USER. The polycom user says the audio is fine. SIP-SIP calls sound good for both parties. Where should I setup the jitterbuffer? The zapata.conf (recent * 1.2) and/or the polycom configs (fw 2.0.3)? Any tips with the zap or polycom settings below would rock. Packet loss - average

B.H. Hello! We have several Asterik boxes that are connected to PSTN using PRI cards and they are interconnected using IAX2 trunks so that incoming calls are delivered from PSTN to the servers they belong to. In past we were using asterisk 1.4 on the server that is receiving IAX connections and everything worked as expected. Recently, we have switched to a newer box with asterisk 1.8.22 and