similar to: Problems with VIA Chipset

Hi, I?ve been following some information about the latest chan_sccp drivers for a few weeks. I installed and tried about any variant of driver that exists in the chan_sccp system. Despite a few little changes in the CLI options I am still encountering a lot of problems with the phone. When not using the phone for a while, it "disconnects" from asterisk (1.0.7) after a few hours

Hi, everybody. I was just running into a DynDNS Problem. One of our phones has a fixed IP, but the * box only has a dynDNS IP and a fixed name. So all phones running SIP are able to "survive" the change of the IP address, but not our Cisco 7920 - it changes state to "connecting to CM0" and hangs there until reboot. After reboot it looks up the current IP address of the * box

The chan_sccp page at http://www.voip-info.org/tiki-index.php?page=chan_sccp2 has been updated. See the bottom of the page. Thanks. Comments welcome. -- respectfully, Joseph =============== ---------------------= ********** =

Is there any problems using this board? I have a dead board in a Book-PC (board size 10.5"x6") so am looking for a new board. Actually I want 2 LAN ports. 'Router' boards with enough umph to run Centos are expensive. I can pick up a VIA epia-m with 512Mb memory for $70 including shipping, so this is rather attractive option. I do have a 100Mb low-height PCI board that I

Does anyone have recommendations for (or against) mini-ITX platforms to be used with Wildcard X100P and TDM400P cards? I am considering the use of systems using VIA EPIA CL and Epia M as small, quiet platforms on which to host Asterisk.

Hi, I have a EPIA mini-itx board that I have been running Fedora 4 on. I want to install CentOS 4.4 on it since FC4 is no longer supported. The install goes fine but when I reboot the machine after the install I get errors like the following: hda:<4>hda: dma_timer_Expiry : dma status == 0x21 There are other errors about not being able to access the disk and eventually the kernel panics.

Dear All Can you please do me favor and let me know how can I check for my CentOS mainboard type ? Please be informed that I want to know if it is as EPIA 500 or EPIA 600 and I am seeking a way to check it as we check for our HDD type via /proc/ide/hda/model . Can you please let me know where such an info can be checked via /proc folder ? Let me thank you in advance -------------- next part

Hi all, im new to Asterisk and to the list. Im trying to run asterisk on a mini-pc with a VIA EPIA Mainboard, the processor is the VIA C3 800. When i compile on the C3, after make, i launch Asterisk and he die with an "illegal instruction" Someone can help me ?? (compiled the CVS on an athlon machine....running ok!) Thanks Marco

Is that a bios setting (I don't recall seeing it) or an OS setting? I run a lot of Via C3 machines (they are so nifty) but don't remember seeing this. -----Original Message----- From: Technical Support [mailto:support@ocg.ca] Sent: Tuesday, September 06, 2005 10:43 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion'; shmaltz@gmail.com Subject: RE: [Asterisk-Users]

Hi Everyone, I'd be grateful if anyone can help with a couple of queries I have. Recently I downloaded Centos 3.3 and cannot get it to install I my system. The system I am using to install is a based on an original EPIA Mini-ITX m/board. At a certain point in installing it comes up with an error saying something like "system not supported". Can anyone advise if they have got

Hi, I was wondering if anyone had a good dhcpd.conf and /tftpboot files for a EPIA-M motherboard with RedHat 9.0.... Or maybe just a configuration that works with the EPIA-M (doesn't matter which type of linux). I'm trying to boot the system from the network and it seems to be getting to downloading pxelinux.0 but then nothing happens after that.... I'm using ISC dhcpd V3.0pl2,

Has anyone successfully run asterisk with a VIA processor ? I have tried unsucessfully, do I have to run make with any specific switches ?

I use them with just the one NIC card. I don't use them as a router so the phones and my gateway are all on the same network. -Jonathan -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Remco Barende Sent: Tuesday, September 06, 2005 4:33 PM To: Asterisk Users Mailing List - Non-Commercial Discussion

Anyone know a good distro for an Epia Mobo with the C3 chip? I have been trying to get Debian and Gentoo installed (new to me) and so far having little luck. Does anyone know a good install for this processor/mobo combo? Thanks Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL:

> Date: Sun, 19 Sep 2004 12:59:52 -0600 > From: Rich Adamson <radamson@routers.com> > Subject: [Asterisk-Users] Re: [Asterisk-Dev] X100p on VIA EPIA-V > problems > To: asterisk-users@lists.digium.com > Message-ID: <Chameleon.1095617288.adar0@vegas> > Content-Type: TEXT/PLAIN; CHARSET=ISO-8859-1 > > > I'm running Asterisk on my (new) VIA EPIA-V

i had such problems on my mini-ITX. when sharing irq's with video or sound card, network traffic during ogg playing (for example on nfs) or quick moving windows crashed the interface. ifconfig down/up resolved the problem. it has been solved for a while now (i couldn't reproduce this problem) i think. regards, OLivier Le Jeudi 12 D?cembre 2002 03:45, The Anarcat a ?crit : >

Hi, haven't found anything in google's, i wonder if there is a comparative page of what to expect from running * on motherboards like the EPIA and similar ones. Since i have not used *ever* such kind of mini atx form factor boards, I have no clue about their performance. SIP-SIP communications, voicemail SIP-TDM communications, voicemail how may users (SIP hardphones and analog phones

I have written a step-by-step setup for installing Asterisk on Debian using the VIA EPIA M platform. It is oriented to the Linux novice (myself being one). Feel free to use it :) http://www.steady-com.com/asterisk/debian-install.html

I'm trying to boot linux on a VIA EPIA-M board (a Nehemiah-based M10000), and I'm having some trouble with it. I'm watching the network transactions with ethereal, and I'm seeing a failure at what appears to be the tftp stage. The M10000 picks up its IP address from the dhcp server (ISC DHCP3), and reports it correctly on the screen. Then the tftp session starts, and I get the

I would like to ask what people think the best way would be to build a low-power consumption, passively-cooled system. For example,one could use a fanless-Eden (mini-ITX/EPIA) system, but the loss of FPU power would limit performance. The obvious choice for FPU work are the Intels and AMDs, nut they're all power-hungry radiators. Is there something that can offer the quiet, power-savings of