similar to: Forcing Asterisk to not bridge/transcode RTP traffic

All, I get this whenever trying to dial to a peer when the peer registered to another server. I'm basically trying to use realtime to check for the peer and dial it. Mar 24 09:16:47 VERBOSE[4527]: -- Executing Dial("SIP/brak-f69f", "IAX2/brak-test/107") in new stack Mar 24 09:16:47 DEBUG[4527]: MySQL RealTime: Retrieve SQL: SELECT * FROM sip_users WHERE name =

Anyone have experience with Sipura's? Anyone know if they offer a warranty? Would like opinions on these, good or flame. We bought *one* to test with and it died, can't even get a response from Sipura "support". Could anyone recommend another device to replace these? Prefer 1 or 2 port design. Ty :-)

Any ideas? I edited the Makefile as instructed, ty. Now compiling .... sccp_channel.c 279 lines sccp_channel.c: In function `sccp_channel_send_callinfo': sccp_channel.c:48: structure has no member named `callerid' sccp_channel.c:49: structure has no member named `callerid' sccp_channel.c:49: structure has no member named `callerid' sccp_channel.c:49: structure has no

Ok, we're trying to use Asterisk as a PBX in our office. Our original plan was to use a Cisco 7960 with a 7914 attached. Short story is, no one updated chan_sccp in a long time and the 7914 is questionable at best anyway from what I've heard. We couldn't ever get chan_sccp to compile, I went to an older version of Asterisk and that broke some of our SIP devices. We tried using a couple

Having problems getting realtime working, I'm trying to use odbc for all of this. I've got Fedora 3 and have been fighting with odbc for a day now. I think I got it working correctly, however I can't seem to get the realtime portion working. In asterisk 'odbc show' shows it connected, I see it on my (odbc) mysql server connected and all, it connects and just idles. So, without

We're looking at implementing Asterisk in our department in the near future, we're looking at anywhere from 15-25 extensions. The machine we were looking at running this on was a Quad Xeon 450mhz (2MB L2 Cache) w/ 1GB of ram. I've heard bad things about running Asterisk on SMP machines? Would we be running into any performance issues with this machine? Tim Jackson Network Engineer

Hi all, i have the following setup PSTN -> routing server (asterisk 1.6.2.11) -> IAX -> callcenter asterisk 1.6.2.9 -> SIP -> agent Does work quit fine - then agent does have the abibility to transfer a call to a third party - the agent can initiate the transfer over a web interface - it does generate a asterisk manager atxfer request... So agent does initiate transfer - call

Hi all, I'd like to connect a softphone at home (nat, dynamic-ip) to a sip-phone in the office via asterisk 1.4.21 (nat, fixed-ip). SIP works well, the phone is ringing, but when I pickup the call, there's no audio on both sides. I debugged the rtp-traffic at home. As long as the phone is ringing, everything is fine. But after the pickup, asterisk sends a SIP/SDP package with its

I have just established a call between 2 sip phones and I have noticed that all RTP traffic goes through Asterisk Server. I was expecting RTP traffic went to one phone to another phone directly. I set canreinvite=yes in sip.conf in both sip peers. I also tested it with 2 mgcp phones and same result, all rtp traffic goes through Asterisk. Is there any way to force traffic to go from one phone

All, I'm not sure how to word this question but we're noticing a lot of our asterisk boxes no longer have multiple asterisk child processes. i.e. doing a 'ps ax' reveals only 1 asterisk PID when normally I'm used to seeing 8+ .. There is no rhyme or reason to it, and we're using the safe_asterisk script which has always worked in the past. Ast 1.2.4, zap 1.2.4, naturally..

Hi All, I have 2 SIP clients configured and connected to Asterisk. When I place a call from SIP1 to SIP2, if both codecs are the same then everything works as expected. I then allowed one of the clients to use alaw instead of ulaw and there were audio problems (couldn't hear the other end, etc). Same thing happened when I tried to use gsm<->alaw/ulaw. Any ideas? I'm using

I have an Asterisk 0.4.0 install working with two grandstream budgetone 100 phones, gnophone, and kphone. This is a private network segment (172.17.x.x), with the PBX configured on my outbound firewall which has a public address (66.x.x.x). - I can make calls between phones - all extensions are working. - I can make IAX calls to IAXTEL. No problems (apparently gsm only) - I can call SIP phone

Hi List; If I need traffic to be directly between the endpoints, then I have to set the canreinvite = yes? If I did not configure the canrenvite at all, then by default it will pass the traffic via Asterisk and not directly between the endpoints? What if one endpoint was SIP and configured with canreinvite=yes while other endpoint was IAX2 and configured with canreinvite=yes, then they can send

Does anyone have some decent Nagios scripts out there that do more than monitor the proc itself? Rather than reinvite the wheel, figured I'd ask. I already saw the one on the wiki. Matt

We're setting up a connection with Level3's voip system and when we use Asterisk or make or recv calls we get an initial pulsing noise. Level3's Interop team explains that's their RTP extension headers and Asterisk apparently doesn't know what to do with it. He said we need to either ignore or of course let the traffic pass. Has anyone heard of this before? I understand the

I asked this question once before with no answer. Hopefully someone can help me as I cannot see a way to do this. I am wanting to differentiate inbound calls voice from FAX. The purpose of course voice gets g729 and FAX gets 711 (ulaw). The problem I'm having is everytime it matches the SIP peer (like it should) but it's always goes to the prefered codec. Anyone have suggestions on how to

Hi everybody, I would like to create SIP call flow Diagram under Windows. Is anybody know a program to perform it? I have already Ethereal and I would like an explicit diagram just to show where something have problems... Thanks Ignace

Hello, Could somebody tell me is it possible to use asterisk without RTP proxying in SIP<->H323 calls? I mean exactly what canreinvite=yes option do in SIP<->SIP calls. I don't need a transcoding, only a signaling conversion, and this is possible with some softswitches, so i wondering what about asterisk. Same question about H323<->H323 calls I'm using NuFone

Ok, here's an odd one. I would have opened a bug on this but last time I tried that I got flamed.. :) Problem: When proxy requests digest challenge (SIP) Asterisk responds normally with the exception that for some reason it changes the FROM: (Also changes Contact: )to what's in the original TO: line. Why on earth is it doing this?! It must be a bug, I've gone over my extensions.conf

ala cisco 7960 -----Original Message----- From: Matt Schulte Sent: Thursday, December 16, 2004 10:34 AM To: 'Paul A Brown' Subject: RE: [Asterisk-Users] Cisco 7960 (SIP) hold problems Sure thing, the biggest problem I had was getting the SIP filenames working correctly for updating the firmware (blah, I love Cisco but these phones are a joke for support). This works for me! Good luck.