similar to: VOIP/SATELLITE

Hello , I'll just started with asterisk and I would liket to to dial between your two phones with to cisco ATA 186 , but I have a problem The two cisco ATA and the server in the same networks and i have the ring in the phone but i'am not able to place a call Between the twe phone . In attachement the sip.conf and a log file Any suggestement . Regards RAbii

I am sure this is really simple. I have a setup of 2 disks (sda, sdb) which are outwardly identical, and are mirrors of each other. Together they form 3 raid1 devices. Both disks can boot. Now sda has bad sectors, and I should replace it. But which one of the physical disks is sda?? The machine boots fine from either one of the disks, (and the booting disk of course is always called sda).

Thomas, Have spoken to Soren, from my bootlog he believes that the problem is in atapicam causing the system to lock up. He is happy to answer some questions but doesnt have time to delve into atapicam himself. Did you author atapicam, I have seen your name on the sourcecode, can you help me further? Whats next? Thanks Adam. -------------- next part -------------- An embedded message was

Hello, I have experienced a dom0 crash where the system became unreachable via the network and the console was unresponsive. I would appreciate help interpretting the logs and any configuration change suggestions. It is a stock Debian Lenny dom0 running xen 3.2.1 with kernel 2.6.26-2-xen-amd64 and an AMD Athlon IIx4 with 4 GB of RAM. It is running 4 VMs. One VM has two PCI NICs being

One of my CentOS boxes has started giving me errors. The box is CentOS-4.4 (i386) fully updated. It has a pair of SATA drives in a software raid 1 configuration. The errors I see are: ata1: command 0xca timeout, stat 0x50 host_stat 0x24 ata1: status=0x50 { DriveReady SeekComplete } Info fld=0x1e22b8, Current sda: sense key No Sense ata2: command 0xca timeout, stat 0x50

I've been having an extremely hard time using the on board SATA controller on my nvidia based board. I have two 160gig Maxtor SATA drives attached to the on board controller, setup as software raid0. The problem is the array is extremely unreliable, where I'm getting constant I/O errors like: sd 0:0:0:0: SCSI error: return code = 0x00040000 end_request: I/O error, dev sda, sector

On Tue, Oct 14, 2008 at 09:52:09PM -0400, John R. Huston wrote: > Hi, I am not very familiar with using mailing lists so if I have made > a mistake in the format or scope of the message please correct me. I > am pretty desperate for an answer by now so any help at all is really > very appreciated. > > I have a Shuttle SD30G2 computer (Specs: >

OK, it seems that the kernel I have (stock CentOS 4.7: 2.6.9-78.0.22.EL i686) seems to gronk the nVideo SATA controller in AHCI mode. It is NOT able to deal with the SATA DVD Burner I have. It is a "Sony Optiarc DVD Burner with LightScribe Black SATA Model AD-7241S-0B LightScribe Support". Is there some special magic I need to do? Here is the relevant bit from the boot up (SATA ports

I am trying to get a pv_ops dom0 working for testing, but I am running into an elf_init error: (XEN) *** LOADING DOMAIN 0 *** (XEN) elf_init: not an ELF binary Full output attached. >From what I have read on the mailing lists, it seems that it is usually a problem with either grub or a corrupt dom0 kernel. Attached is my kernel config (2.6.28-rc6-tip). I followed the instructions on:

I recently came across an enormous cluster of x86 clone machines running fedora core 1 (2.4.24) which have typically all intel or amd have VIA IDE chipsets. They frequently experience corrupted journals rendering the ext3 partition in read-only mode. More important than recovering the filesystem, I am interested in finding the root of the problem. The common hardware that all of these

Hi, I have a server (Dell PowerEdge SC1435, ServerWorks HT1000) on which I'd like to try installing FreeBSD. I've already failed to make 7.0 work on this box and was wondering if you have information about the behavior of the upcoming 7.1 on this hardware. I've been following the "HT1000 chipset errata saga" thread, and the commits by sos@ to CVS (around Jan 2008), but have

Hello all. I just updated my machine from 9-STABLE to 10-Stable today. beasty ~ # uname -a FreeBSD beasty.schavemaker2.local 10.0-BETA3 FreeBSD 10.0-BETA3 #0 r258543: Mon Nov 25 13:23:31 CET 2013 root at beasty.schavemaker2.local:/usr/obj/usr/src/sys/KRNL amd64 After a reboot, the console gets cluttered with a lot of messages. ata2: FAILURE - zero length DMA transfer attempted ata2: setting

Hi all, I installed CentOS 5 on DELL machine. Then, When the system comes up, I always get below erros. Could you pls help me to solve this out before I setup this box for productiuon use ? these are errors. usb 1-2: device not accepting address 2, error -71 ata2: port failed to respond (30 secs) ata2: SRST failed (status 0xFF) ata2: SRST failed (err_mask=0x100) ata2: SRST failed (status

I''ve been following unstable day to day with mercurial but I''m still having a problem with my HVM testing. I using the i686 Centos + Bluecurve isntaller and I get the following error in the guest during disk formatting: <4>hda: dma_timer_expiry: dma status == 0x21 <4>hda: DMA timeout error <4>hda: dma timeout error: status=0x58 { DriveReady SeekComplete

Hi all, I need to test the following scenario: +-----------+ +-----------+ | asterisk 1| | asterisk 2| +-----------+ +-----------+ | | | | _______|__________________|___________ | | | | | | +-------+ +-------+ | ATA 1 |

I am having problems getting my 64-bit Debian Squeeze (Xen version 4.0, Linux Kernel 2.6.32) dom0 to recognize a harddrive connected to a secondary sata controller. My motherboard is a Gigabyte GA-X79-UP4 and has two sata controllers. The first is controlled by an Intel X79 chipset and the second is controlled by a Marvell 88SE9172 chip. During the initial install of Debian everything is fine and

I am attempting to install 7.1-BETA2 (from CD) onto a PC with a Promise SX4060 RAID controller and two Seagate 120GB ATA disk drives. The boot from CD keeps repeating the following (error) messages: (I'm retyping here) ============================================================================ ================== ad4: WARNING - SETFEATURES SET TRANSFER MODE task queue timeout - completing

On my C5 machine (a Dell XPS420) I have a 500Gb disk on the internal SATA controller. I also have a SiI3132 dual-port multi-device eSATA card. This is connected to an external SATA array of disks. Now occasionally I see something like this in my logs ata7.01: exception Emask 0x0 SAct 0x0 SErr 0x0 a ction 0x0 ata7.01: irq_stat 0x00060002, device error via D 2H FIS ata7.01: cmd

Hi, according to http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/dev/amr/amr.c?only_with_tag=RELENG_6 it seems MegaMGR for linux now can work. Any experience? -- Cris, member of G.U.F.I Italian FreeBSD User Group http://www.gufi.org/

Hi, Does anyone have any experience connecting Asterisk to a Meridian system using an ATA2 and x101p? The basics work -- I can make outbound calls, receive inbound, and use flash to transfer calls, but certain things do not work, specifically with calls from internal extensions. - Does the Meridian/ATA2 pass any kind of callerid info? We do not have external callerid, but I'm not even