similar to: 3 x TDM400P in one PC ??

FYI, asterisk DOES now support g723, but you have to pay for it: http://store.yahoo.com/asteriskpbx/asteriskg729.html -----Original Message----- From: Dan Fernandez <danfernandez00@hotmail.com> Date: Mon, 5 May 2003 17:33:05 -0300 To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Has anyone gotten SIP_CODEC= to work? Basically, since I?d like to use g723 for sip

Hello list! I?m working on a fresh Asterisk install over CentOS7 base. I?m using ?Asterisk. The Definite guide? book as a reference. I connect and work using SSH Problem I have - I can?t connect to asterisk from remote. Getting error: $ sudo asterisk -rvvvvvv Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) Yes, it exist, and service runs: [asteriskpbx at

It would be nice if Digium updated the hardware compatibility list on asteriskpbx.org to indicate that the LineJACK can't be used for dialing out. I've seen several people on IRC be burned by not knowing this. --Eric -- BTEL Consulting 850-484-4535 x2111 (Office) 504-595-3916 x2111 (Experimental) 877-552-0838 (Backup Phone)

Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware

Hi list, To make outgoing calls by skype i would like to have our crm app create callfiles like we do for normal calls. If i read the instructions it says this : ---quote--- The syntax for making an outgoing call using Skype for Asterisk is as follows: Dial(Skype/[<originator>@]<destination>) ---unquote--- So i create a callfile that looks like this: --- Channel: SIP/228

HI all: I have spent a large amount of time configuring/installing phones connected to Asterisk. Halfway through the process I discovered that my Cisco7960 with 2 7914 expansions was not supported in the SIP protocol. After reverting to SCCP 6.0(4.0) I am now perplexed with the hassle of configuring SCCP to properly work with Asterisk. So far I have gotten the phone to dial and receive calls

<div><BR>Hello,</div> <div>&nbsp;I bought a TDM400P, and intended to use it with my analog phone, which is RJ11 ofcourse. So, the question now, how do I plug in my RJ11 phone to the TDM400P card, which has an RJ45 interface? Also, since it's an 11B card, I also intend to bring in an analog line into the RJ45, so i am still left with the same question....how do I go

I've been searching the Internet for information regarding the replacement of astdb with a modern sql engine. There are several reasons one would like to do this. First of all, external applications have a hard time reading/writing to the now-old astdb format. Also (and this is what interests me most), the sql astdb could easily be clustered throughout several servers (I'm looking for a

I'm looking to add a single FXO port to my Asterisk box. It looks like my options are a Digium Wildcard X100P off eBay for $6.99, or a Wildcard TDM400P with an FXO Module from Digium for $125. Can anyone explain the tradeoffs (other than the ability to put 4 FXO/FSO modules on the TDM400P). What about RTC for the system - I know the TDM400P provides it. Does the X100P? Thanks!

Hi All, I'm attempting to use two X100P cards and one TDM400P card. What driver do I load for the TDM400P? Is their any documentation for this card yet? Also, I know this has come up before but I can't seem to find it in the archieve... how do I configure the second X100P card? Anyone have a working sample? Thanks in advance, Randy

We are experiencing problems with FXO modules on TDM400P. From time to time they stop responding to incoming rings although they work fine if we use them to dial out. It's been verified at least in two different installations (using different mainboards) in two different locations. The only solution to the problem is to stop asterisk, then unload and reload kernel drivers. The problem appears

Hi, Everybody, I can modprobe TDM400P card without feeding power supply , so what is the purpose of providing power supply in that card. Can any body tell me Regards Lokesh Portugal mail -lokeshkumar80@yahoo.co.in ____________________________________________________ Send a rakhi to your brother, buy gifts and win attractive prizes. Log on to http://in.promos.yahoo.com/rakhi/index.html

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 49 bytes Desc: bullet.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050125/1dbc7ddf/attachment.gif

Is there a digium twitter 'user' to follow that only tweets important announcements and release information? If there is not, I think there should be. It would be highly utilitarian to get an SMS when there is an update to Asterisk, Dahdi, ADA etc, but I don't want to be bothered real-time with asteriskpbx tweets like: "Anyone trying anything cool with Asterisk over the

Anyone in New Zealand using AsteriskPBX? If so, what hardware are you using to connection to Telecom's lines? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030619/d5c12ca0/attachment.htm

Hi, In digium website. http://store.yahoo.com/asteriskpbx/newitastdmde.html It is said Dev Kit PCI card works with 2.4 kernel. I am wondering if it is also working with 2.6 kernel? Anyone knows? Thanks Michael

I would like to hear from anyone good or bad as what their experience has been in recent times with STABILITY of current builds of Asterisk and drivers for TDM400P. The sort of configuration is: 6 incoming POTS lines. ie. 2 TDM400P cards. I am not concerned with: price points, or the advantages or disadvantages of using POTS vs ISDN technology, but simply RELIABILITY & stability of the

What are peoples experience with the reliability of the TDM400p. Specifically in the 2 FXO, 2 FXS configuration, which is the 022 (?) model. Is this board prone to random failures? joe a.

Has anyone come up with a way to get power to a TDM400P card installed in a Dell PowerEdge 1750? Thanks, Adam The contents of this email message and any attachments are confidential and are intended solely for addressee. The information may also be legally privileged. This transmission is sent in trust, for the sole purpose of delivery to the intended recipient. If you have received this