similar to: DTMF tones not working

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This is slowly driving me nuts! I have several Cisco 7960s with SIP 8.2/7.5 fw connecting to Asterisk 1.2.5 driving a TE110P on a BT EuroISDN PRI line. On all outgoing calls I get a double ring tone (UK style + US style). I also have a DECT phone on a Sipura SPA-3000 configured with UK tones. This gives me a double ring of UK + UK, so this

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

Hi, My system is like this currently: ATA-186 <-> *1 <-> IAX2 to Europe <-> *2 <-> i4l <-> voicemail at cell provider When I dial up to my voicemail at my European cell phone provider I can't press '#' to get into their menu. It seems like it just ignores any DTMF tones or doesn't get them. When I call a human on the other side of the i4l they

I run a bunch of the Linksys ATA's.. I always use rfc2833 for DTMF. works very well and have never had a problem with it. ..o-------------------------------------------------------o. Brian Fertig NOC/Network Engineer Planet Telecom, Inc. Tampa, FL Office -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of

I just loaded from CVS this afternoon and in the debug output I see... DEBUG[76820]: File chan_zap.c, Line 3254 (zt_read): DTMF digit: m on Zap/16-1 DEBUG[76820]: File chan_zap.c, Line 3254 (zt_read): DTMF digit: u on Zap/16-1 I knew about DTMF 0-9, A-D, *, and #, but I didn't know about m and u :-).

Hi, We have few systems with asterisk 1.4.22.1 and we use sip trunking for them not PRI's, one of our system is giving a problem of dtmf (rfc2833), like when we dial the number that have IVR and enter the extension or access code, it some time takes it and some times does'nt recognize the digits dialled. We also tried auto and info for dtmf but could not get the dtmf to work reliably, can

I have a couple of Linksys PAP2T-NA & Grandstream HT-502 extensions that are receiving random DTMF tones on their side, but that are not heard by the outside party. I have been using Asterisk 1.6.6 through 1.6.10 and have always had this issue. I am only using SIP on the Asterisk server and all extensions and trunks are set to rfc2833; outside of this issue DTMF operation works fine.

> I have seen the following effect in Asterisk, though: where > it converts > an inband DTMF (eg coming off a Zap channel) into an > indication, it mutes > the audio where that tone is. But sometimes it leaves a > teeny bit of the > tone behind. > > If you take such a call over say IAX to somewhere and then > back out a Zap > channel, you end up with the

Hi, folks. I have a problem using Asterisk 1.2. I create conferences using app_meetme and Zap channels, and for every participant I run the script defined by AGI_BACKGROUND_SCRIPT to be able to listen and react to DTMF tones. As the docs tell me, when using the AGI background script one loses the ability to control the meetme conference via the command line so for muting conference participants I

Hi, My Asterisk systems runs like a dream with mISDN, SIP and even and old Digium board. But have almost in every conversation some irritating DTMF being generated. The seems to be just as often from all trunks but are worse if noise load speaker in other end. Any good advices? Where to look for forgotten DTMF detection settings? Thank you! HB

Hello list, Hope you are all doing fine! I have stumbled over some piece of dialplan code in which apparently they were trying to avoid recording the DTMF tones in the wav file. It is really messy and I am not sure if this really works. So after a bit of research I found this comment ( https://community.asterisk.org/t/asterisk-dtmf-record/65040) in which it is said: *"Asterisk strips the

While most cell phones are fine, some cell phones don't seem to produce DTMF digits that Asterisk/Zapata will detect. One of our salespeople has an AT&T model that never gets any digits through. Is there a known solution? I understand, of course, that with cell phones the DTMF tones are actually created at the base, and that pressing the key longer usually does not result in longer

> Hmmm... I have this aweful feeling that I'm choosing the > exact wrong time to ask a "newbie question" :) Oh well, here > it goes. > > The quick question is : "How do I dial an extension?" > (answer is probably - "you don't" in which case:) "How do I > dial my asterisk box?" - I have no outside line, I just want >

Hi, We are experiencing this issue of redial dtmf tones generated randomly in the Voip calls, we have asterisk 1.4.21.2, dahdi 2.0.2.2 and we have dtmf as rfc 2833, we have a cisco router at the location Cisco 2431, 8FXS (only one FXS is used for Fax and rest are empy) connected to the netgear switch and all the phones are connected to this switch and there are no non sip devices in the

Hi, I have asked this question months ago - i have "toggled down" all DTMF Recognizations in my Asterisk (no more features etc) and found more people which recognized the same problem, but i cant find any help for them and me. The Problem (short as possible) : In a randomly call in my business day some unit in my Asterisk System sends an randomly DTMF Tone, like "A"

Topology: PSTN<-T1 PRI->NEAX2400<-T1 PRI->Cisco 3825<-Ethernet-> Asterisk VoIP server When I make a call to a VoIP user from the PSTN, the call gets routed through the PBX, and Cisco. Because of that the DTMF tones are passed inband, which I can hear on the VoIP end of the call. However, I have one extension on asterisk set up so that I can check voice mail when away from my

I have progressinband=yes in sip.conf, but Asterisk sends a 180-Ringing to my polycom phones and then it also sends 183-Session Progress. That doesn't seem to make sense. Shouldn't Asterisk NOT send 180-Ringing if progressinband=yes ? Doug.

Dear friends, As I commented some while ago in the list, occasionally when DTMF Tones are sent, they appear in RTP Payload and in Events too, producing duplicate tones being recognized. This behavior happens in Asterisk as well as in Gateways such as Cisco, for which we had the opportunity to observe the error and extensively debug it. We ended up recognizing good digits by adjusting audio gain

Guys. I have a te100p with unicall and an E1 and Im having problem with DTMF tones but the weird thing is, I only have problems sending the tones to certain phone numbers, anybody seen this behavior? Asterisk shows on the console the dtmf tone been pressed but seems the other side is not getting them, and this just happens with certain phone numbers, not all.. Any clues(tips?