similar to: Group channel rotation for outgoing call?

Hey all, I have a situation where I have 8 lines from the phone company in a hunt group coming in to my asterisk box. These are the same lines I'm using for outgoing calls ( named g0 ). The problem arises when someone dials our number at the same time asterisk tries to put a call out on one of the zap channels in the g0 group. This has happened twice that I know of so far, once to

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

When I try to patch the Makefile for asterisk with the Apps_makefile.patch from Spandsp I get the following error. patching file Makefile Hunk #1 FAILED at 47. Hunk #2 FAILED at 76. 2 out of 2 hunks FAILED Has anybody seen this.

Hello All !!! I have 4 PSTN lines in the PBX server 1,2,3,4. First line will be used by only one extension (i.e. for the boss) for incoming and outgoing. This line is dedicated for him only.( The remaining lines will be shared by the employees 1) Group A have access to lines 2 , 3 & 4. 2) Group B have access to lines 3 & 4 3) Group C have access to line 4

Hi. We have 3 channel for _outgoing_ calls and would like to use them equally (by turn). Is there any 'queue' for outgoing calls? Now I have to select the second channel manually when the first is busy and so on. Does Asterisk have any functionality to do it automatically?

hi, Can anybody pls tell me, how to increase the time gap between 2 digits when you transfer a call. ie, the operator answers the call, and presses hash key to transfer, and then enters the extension number, some times, it timeouts too quickly before the operator enters the whole extension number (may be bcos the operator is slow). I tried the following, but it doesn't seems to be helping

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

Hi all, I try to found some information about if possible has dump-files that rotate automatically. I has setup: <dump-file>/recordings/stream-%Y%m%d-%H%M%S</dump-file> How is the correct way to split every 1 hour for example this dumpfile? Thanks Alejandro -------------- next part -------------- An HTML attachment was scrubbed... URL:

Will the FXS cards that work with asterisk handle rotary? Are there any channel banks that can convert rotary to touch tone (like some sorta bridge)? The goal is to be able to log input from rotary phones. Full PBX functionality would be nice but... (It's for a project, not for serious production). -- // Ethan O'Toole //

Folks, I've got one of those GPO 1950's rotary dial phones that I'm trying to get working in the UK. I've got pretty much everything working with my TDM400, the phone rings and I can receive calls but I cannot dial with the rotary dialer. I have set pulsedial=true or whatever the exact setting is and I can dial from the phone by lifting the receiver and tapping out the number on

Ok... I am not a telephone guy... I was born after rotary phones, so forgive my ignorance in this matter. I am trying to get a really old rotary phone up and running with an ATA. Why? Who knows... just thought it would be cool. The problem is that it does not have an RJ11 connector, instead it has three wires (green,yellow,red). Does anyone know what that type of connector is called? Or

Dear friends, I want to sort a dataset according to one or two variables in the dataset, i thought sort could do it , but failed. e.g. x <- c(2, 9, 18, 3, 2) y<-c(2,5.6,5,9,8) z<-c(21,5,5,19,7) a<-cbind(x,y,z) a x y z [1,] 2 2.0 21 [2,] 9 5.6 5 [3,] 18 5.0 5 [4,] 3 9.0 19 [5,] 2 8.0 7 I want to sort dataset a according to ascending x and descending y, How to

(Forwarded off-list message) -------- Original Message -------- Subject: Re: [Xapian-discuss] what is the fastest way to fetch results which are sorted by timestamp ? Date: Thu, 11 Aug 2011 01:06:36 +0800 From: ??? <panjunyong at gmail.com> To: Tim Brody <tdb2 at ecs.soton.ac.uk> On Wed, Aug 10, 2011 at 6:39 PM, Tim Brody <tdb2 at ecs.soton.ac.uk> wrote: > Hi, > > In

I'm trying to use a couple of old Western Electric type 500 phones (desk model, rotary dial). These phones work fine, as tested with telco lines (they dial, receiver/transmitter works fine, etc). I'm running Asterisk 1.6.2.11. I can't get them to dial through Asterisk. They are connected to a Rhino channel bank which is connected to Asterisk via a Sangnoma card (T1 with echo

Hello, I have two FXS port on my TDM card. channel 4 is attached with a telco line that I use frequently. And channel 3 have another telco line. but I dont publish that number to my friends. If I receive a call through channel 4, how can I handover that call to channel 3 ..so that I can keep channel 4 open for incoming call. Thanks,

Hi, In the order() help file, there is an example like: a <- c(4, 3, 2, NA, 1) b <- c(4, NA, 2, 7, 1) z <- cbind(a, b) (o <- order(a, b)); z[o, ] How can I do something like "order a in ascending order, b in descending order"? And say I have a third vector c, and I'd like to add this to the previous condition "a ascending, b descending, c

To all Asterisk guru's... Here is my question. 1. Asterisk PBX - 5 Trunks / Incoming lines 2. 1 Building - 3 Companies (sharing phone system) Ok that's the basic layout. Here's the low down - Each company will have one dedicated channel for there company. The other 2 channels they want to be set aside as rollover's (rotary). That is not an issue. Where my concern is, how

The subject says it all. Is it possible, code wise, configuration wise, at all - to reverse the order in which the available zap channels are used for *outgoing* calls? Code wise, I looked at the channel structure and it appears as though there is only a next pointer, not a previous pointer, so to 'easily' to this in the code would require a change to the code that reads in zapata.conf?

My fellows, We have Asterisk@home installed and we want to interconnect it with our existing quintum gateways.. any idea how to config that? Your time is very much appreciated.. Cheers, Jessie -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050220/2518797c/attachment.htm

Hello all, Does anyone know how to make R graph the x-axis in descending order? I am all set in creating a vertical bar chart using either the plot or the xychart (in lattice), but I need the x-axis in descending order. I have tried resorting the data but apparently R automatically graphs the x-axis in ascending order. I have multiplied the data used for the x-axis by -1 and this works but now