similar to: No recorded messages

Hi, guys, For my server, if i use my handphone to call in the PSTN line by TDM400p card, the server could not receive the caller id correctly. anyone knows the problem? I am currently using asterisk 1.2.14 with freepbx 2.2.1. The CLI is as below, "Caller ID name is 'zap1' number is '4521'" , this 4521 is one of my FXS zap extension created. dialparties.agi: Starting New

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

Hi This is hard work :) I have read the Asterisk Handbook, BudgeTone User Manual, Andy Powell's useful notes, Zac Sprackett's Asterisk Resource Pages and more. I am not a linux newbie but am new to Asterisk. I have failed to find any docs that explain how to get a very very simple, minimal, system up and I am trying to get the following to work: 2 BudgePhone 102D connected on a LAN to a

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

Hi people, I have the following dialplan, but it doesn't have the behavior that I think it should have. [default] exten => 2001,1,Answer exten => 2001,n,Dial(local/3005) exten => 2001,n,Hangup exten => 3005,1,Set(__RINGTIMER=10) exten => 3005,n,Macro(exten-vm,novm,3005) exten => 3005,n,Hangup When I execute the Originate (AMI) with the argument Channel=local/2001, It rings

Hi ALL Have installed asterisk@home 1.0 On FWD DID's, appears that 2 calls are generated to the inbound extention. I have confirmed this on a number of friends boxes also. Does anyone have a fix for this ? I set the DID simply to a custom context and it did the same... Anyone have a way to fix this ? Here is the output...... -- Accepting AUTHENTICATED call from 65.39.205.121, requested

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

I have a customer running Asterisk 1.4.22 and FreePBX 2.5.0 that is having problems with Voicemail. They can listen to their voicemail but on the weekend it stopped delivering messages via email. The only thing I can notice is that the permissions for the files on teh voicemail directories are created with no permissions at all. Here is the listing on one of the mailboxes: 4 -------rw- 1

Hi, I set up a ring group. I would like for people who select a certain voice menu option to ring a list of extensions (I have just one extension in there at the moment) and if it doesn't answer to go to an extension's voice mail. I am using a version of asterisk from CVS, last updated a couple of weeks ago. This line in extensions_addtional.conf sends the call to ringgroup 3 if

Hello, i've recently switched over from 1.0.9 to 1.2.3. I've experienced some (to me) weird behaviour. This is the config for an example queue.conf: [654] wrapuptime=30 timeout=20 strategy=ringall retry=5 queue-youarenext=queue-youarenext queue-thereare=queue-thereare queue-thankyou=queue-thankyou queue-callswaiting=queue-callswaiting music=default monitor-join=yes monitor-format=

OK, i've got asterisk @ home 1.3 up and running with Broadvoice. BUT I have one nagging problem to sort out. When you call my BV # the calling party gets no ring indication, just silence until either I answer the phone, or the call bounces over to voicemail. below is the console output when a call is recieved. what am i missing here? thanks Bernie -- Executing

Whenever I try to drag calls to the Parking Lot or On Hold, FOP would drop my calls. I have searched online and have found similar problem, such as the link below. I have tried their solution but still the FOP is not working correctly. I even installed the HUDLite server and is getting the same results. www.freepbx.org/forum/freepbx/users/flas...ot-transfering-calls Here is the log when I tried

chan_sip.c6524 reload_config= unable to get ip address from asterisk, sip disabled The ip address is working fine, Internet works great. Can anyone help...Thanks

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs

There is an environment Setup uses Asterisk 1.2 and doesn't want to upgrade. There is an issue while a call goes to any queue we create, the call is being disconnected after 20 seconds and it is hangup. The following is the configuration: - vi /etc/asterisk/queues_additional.conf [8] wrapuptime=0 timeout=30 strategy=ringall servicelevel=5 retry=4 reportholdtime=No queue-youarenext=

Hi i have installed AAH 2.6 and configured some extensions the calls are working fine. but if i dont answer a call then it says " the person at extension " and hangs up . it doesnt spell out the extesion number nor it goes to voice mail box. *************************** Asterisk CLI log **************************** dialparties.agi: Extension 200 is available...skipping checks --

Hello, I have setup a test server with asterisk/AMP and have several 7960's connected to it. The asterisk server has a public ip and all the 7960's are behind nat'd routers. When I try to call from extension to extension I get directed straight to voicemail. I do not have any cards installed and instead direct everything to an Ondo server. I have been told it's not an AMP

Hi, i have a HT 488 and I want using this like an FXO for Asterisk. I have find some configuration in the list archive & google but my HT with these config not work. my sip.conf [HT-488] username=400 type=peer secret=wowowow qualify=yes port=5062 nat=no host=192.168.1.157 fromuser=400 disallow=all context=from-pstn allow=g711u allow=ulaw allow=alaw my sip debug:

Hello! I have a number of IAX clients behind a NAT (on the same LAN) and asterisk server on the Internet. And that clients doesn't speak directly to each other, traffic goes through the asterisk server. What should I configure to make IAX clients on the same LAN to speak directly, please? notraster=no is set in iax.conf The asterisk server is on real IP behind a NAT (at DMZ with full 1-to-1

Hi I've been looking for 10 minutes and cant find dialparties.agi Can anyone tell me what folder this is located in as I'm going crazy. (if it makes a difference I use asterisk@home and am replacing the AMP dialparties.agi file) Super big TIA, Dean -------------- next part -------------- An HTML attachment was scrubbed... URL: