similar to: Netlogic inbound DID issue

Has something changed in the recent modifications to Asterisk that would break dialing of the IAX peer? We're getting these authority failures everywhere. Everything is configured just the way it was half a year ago, this is the message we're getting on the most recent vers of asterisk. Wiki says nothing, nor does the ast-dev list.. -lost Mar 18 12:55:23 NOTICE[3479]: chan_iax2.c:6545

Hi All, I'm having problem with IAX, I'm trying to connect to speex.co.il from asterisk using: register => username:password@speex.dyndns.org and I cant get it to work. Maybe someone who already got this to work will help... When dialing my speex extension I see the next output from consol: IAX2 Debugging Enabled *CLI> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno:

Asterisk Users, I am running Asterisk 1.2.13 on Debian Etch with McLeodUSA's T1 service. I have two Netgear switches on my T1 router, one for VOIP and another for data. I use a gigabit switch for all VOIP and a regular 10/100Mbps switch for all data. This morning I saw this message a few times on the Asterisk command line. The lagged cause garbled phone calls. Is my network to

Ok, here's an odd one. I would have opened a bug on this but last time I tried that I got flamed.. :) Problem: When proxy requests digest challenge (SIP) Asterisk responds normally with the exception that for some reason it changes the FROM: (Also changes Contact: )to what's in the original TO: line. Why on earth is it doing this?! It must be a bug, I've gone over my extensions.conf

I would like to ask, if someone observe also problem with peer qualify problems, my asterisk log is full with UNREACHABLE/REACHABLE messages, even when two asterisks are in LAN environment, please take a look into this debug, I can't find any problem with packet loss, all qualify requests are replied and acknowledged, I will submit bug report, if you will also not find any problems here...

On the asterisk1 I got this: register => username:secret@ipaddress2 [eop] username=username secret=secret type=peer host=ipaddress1 auth=md5 on the second box I got this this host is ipaddress2 [incommingiax2] username=username type=user secret=secret host=dynamic context=from-internal-custom auth=md5 on first host 1 am getting: Jun 22 14:42:10 NOTICE[2398]: chan_iax2.c:7411

I run a phone in a remote office using the IAX2 protocol. It mostly works fine; except that every 5 mins it loses connection with Asterisk, before reconnecting 30 seconds later; rinse & repeat. Using the IAX2 debugging, I'm seeing this a lot: Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: POKE Timestamp: 00018ms SCall: 04050 DCall: 00000

Hi, I'm testing an upgrade from 1.4.18 to 1.4.37 in a VM prior to putting it into production. Ive done this by installing 1.4.18 onto the VM, putting my config files in place and then installing 1.4.37 over the top (which is what I'd have to do on production). I've found a few issues in the config files, but nothing I couldn't handle until... I hit inbound IAX issues. My

Hi all, I am trying to connect to a softphone application using an Iax channel on Asterisk 1.4.30. I can do outbound calls, from softphone to asterisk, but not inbound from asterisk to softphone. I get the following Debug: ---------------------------------------------------------------------- ---------------------------------------------------------------------- Tx-Frame Retry[000] -- OSeqno:

What settings are people using? I've seen the ones from dslreports but I'm in that lucky group of people that paid the 1 euro just to have it no longer work. Even after I setup a additional account over the weekend it still doesn't work. And, of course, etherreal only shows encrypted traffic so I can't snag any config settings from it. Any assistance? -----Original

I am having some problems getting TelIax service to work with *. Outbound calls work just fine. When I try an inbound call the phone rings and there is no audio. Upon further investigation "iax2 show channels" indicates that the codec is "unknown" The provider confirmed that they are set for ulaw and so am I. Does anyone have an idea what could be causing the codecs to

All, I run a bunch of (well 20+ actually) Asterisk boxes at home, work, friends and the lie with our own dialplan in the form 8EEXXXX where 'EE' is the exchange number and 'XXXX' is the extension number. This arrangement has been in for 2+ years and worked well with a central box (asterisk.thorcom.net) acting as the routing hub and SIP exchange point with various public

This may not strictly be an asterisk question, but not sure where else to post ... I have an Asterisk test server setup with two firefly clients, one on the local lan and one on an external ip address. Both clients are setup the same way and voice calls work fine. The asterisk console reports a "Registered" message for the external client at about one minute intervals but the

I'm new to this list, and I apologize if this is an already answered question, but my Google-fu was not strong enough to find the answer if it was. I'm having a problem with DTMF on incoming IAX calls. For the first few seconds of the call (between maybe 1 and 15, it varies from call to call) everything works fine. After that I continue get DTMF_E messages from the remote IAX server

Hi everyone, THis is my second thread regarding the issue.(before I was having problems with accessing my email, which slow down my responses, sorry for that) My setup looks like this Firewall | | Asterisk---Asterisk (two asterisk servers with the same setup for high avail) | | phones Ports 5060, 10000-20000, 4569, 5036 are forwared to 192.168.1.251 which is virtual ip address on one of the

Hi, I'm using http://www.portunity.net/ I configured now asterisk with the following setup: iax.conf: register => XXXXXXX:YYYYYYY@iax.iaxport.de [portunity-out] type=friend host=iax.iaxport.de username=XXXXXXX secret=YYYYYY context=incoming-portunity notransfer=yes [guest] type=user context=default ;callerid="Guest IAX User" And in extensions.conf: [default] ;exten =>

I have something going on that I don't fully understand after a weekend of looking for answers. I have an iax account with Tesco that works flawlessly with the Zoiper client - but is giving me trouble with inbound calls in Asterisk 1.6. After some playing I have ended up with an iax.conf file that looks like this: [general] calltokenoptional = 77.75.0.0/255.255.248.0 maxcallnumbers = 16382

Hi My head hurts... Can anyone help out here, my remote IAX can see my local IAX and visa versa, conversation starts, I can dial my remote (POTS) landline number, remote end answers, trys to route to local iax2, I see it start the conversation here, the extension (SIP) rings once and then it dies... Both ends are defined with accept IPADDRESS to keep it in the family and simple.. Debug info

hallo, i am really confused how nativ briging is working with asterisk, i use a asterisk server as central server and register another asterisk and an iaxcomm client to the server, all three have public ips on the internet. somtimes, when i call from iaxcomm to my asterisk, the calls go peer to peer (i can see it with tcpdump) but sometimes the get routed through the central asterisk server

Hi I've 3 iax connections to my provider , each of them have own DID , PH1<----| | \/ PH2<-->|-----| <---------------------------> |----|<-- DID1 | A1 | <---------------------------> |ISP |<-- DID2 PH3<-->|-----| <---------------------------> |----|<-- DID3 I had iax phone on each of this connection , but now I want to terminate all