similar to: Cisco 7960 SIP 7.4

Is there a way to display the time of the 7960 running firmware 7.4? Im unable to find any information. Thanks, Ben Blakely -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060308/a7e575cc/attachment.htm

Hello all, I've got a Cisco 7960 running version 7.4 firmware (heard there were problems with 7.5) and I can't get it to register with Asterisk. I've stripped down my configs on the phone to a bare minimum, and posted them below. Basically, the Cisco phone sends absolutely no packets to the proxy when it gets booted. If I make an outgoing call I see traffic getting to Asterisk, but

I have been able to upgrade my Cisco 7905G phones to the SIP Image without any problems, but I just got a 7960, and I can't seem to get to the settings so I can upgrade to a SIP Image. When the phone boots up, it says Configuring VLAN, Configuring IP, TFTP ????..., then Protocol Application Invalid. I noticed on the wiki page "Firmware issues on 7940 - 7960"

Dear All, I'm trying to configure my new phone Cisco 7960 to work with asterisk. I followed http://www.asteriskguru.com/tutorials/cisco_7960_ip_phone_configuration.html and I got into the point where I can see on the the display line indication showing "55 <phone icon with x>" so it looks like the phone is not registered. The phone and the asterisk are in the same local

Does anyone know if version 3.1 is Call Manager or SIP? Thanks.

Hello all, I've got myself into a bizzare situation that I can't seem to get myself out of... Was wondering if anyone had some advice that might get me 'over the hill' on this... Some background: PBX consists of an Asterisk box (running TrixBox), 4 Cisco 7960's, 2 Polycom IP500's, and now an additional Cisco 7960. The phones are all on a separate LAN. There is

Hi all, I have looked at cisco docs and it says DND is set by pressing the services button and choosing DND. Does anyone know how to configure DND in the services.xml file. I've googled around and not found anything. When you enable it in SIPDefault.cnf it just allows you to use it once. Many thanks for all your amazing work. Daniel Niasoff

Gents, I've built an Asterisk system to replace our PBX at work and have Cisco 7960 phones (SIP 7.4) running with Asterisk 1.0.7. How to I get Asterisk to recognise the '#' being pressed during a call? In sip.conf I have entries likle this: [2001] type=friend context=local-phone auth=md5 username=2001 secret=xyzzy callerid=Jack Tubby <2001>

Typo in your OS79XX.TXT P00 ? instead of P0S !? -----Original Message----- From: Michael L?jtnant [mailto:ml@zyxel.dk] Sent: 17 August 2004 13:31 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Cisco 7.2 firmware for SIP 7940/7960 released Hi Shaun, Saw you post, and rushed to their ftp-server and downloaded it :-) But, I can't make my phone (7940) upgrade, so maybe you

I know this is a little off list but I can't think of a better place to ask this question. I upgrade the phone to 7.1 and it installed the Universal Application Loader. Now I'm getting Protocol Application Invalid after it reads tftp SIP(MAC).cnf Any ideas? Again sorry this is off topic

<div><br><div><br><br><br><br><br><font color="#990099"><br></font><blockquote style="border-left: 2px solid rgb(0, 0, 0); padding-right: 0px; padding-left: 5px; margin-left: 5px; margin-right: 0px;"><div><div><br> <asterisk-users-request

Hi All, Just a heads up - I was looking around the Cisco FTP a little while ago and noticed that the SIP 7.2 images for Cisco IP Phone 7940/7960 were released yesterday (16th August). No new features - all bug fixes according to the release notes. I've already started using it. I thought those of you running the Cisco phones and the appropriate access who didn't yet know would like to

Hi all, i have a problem with some cisco 7960. Yesterday i did a firmware-upgrade from 3.1 (1.2) with P0S30203.bin as described in the most documents. Now i get the message Phone unprovisioned and in TFTP-Log i find the following line: 07.03.2005 19:58 :Timeout error sending P0S3-07-3-00.bin to 192.168.0.83, 0 bytes So i think it now wants to load the file P0S3-07-3-00.bin. But i have not

Hi everyone, I googled this followed the instructions, but it hasn't work for me yet. I have universal setting in SIPDefault.cnf and phone specific settings in SIPXXXXXXXXXX.cnf. But it doesn't get registered. I need to register it on two different asterisk boxes. So my SIPXXXXXXXXXX.cnf looks like this: phone_label: "Zeeshan A Zakaria" line1_name: "523"

Here's a clip of comments lifted from a Cisco bug list. This will be perhaps useful to those of you who have just purchased a Cisco phone off eBay. JT ------------- (1) Short problem description: Documentation on how to load SIP image on phone with skinny software (2) Longer problem description (what happens): If the phone is loaded with the Cisco Skinny code, then there is a small

Hello, When I restart asterisk the cisco 7960/7940 phones (sip fw 7.5) fail to re-register themselves with asterisk, even though I put "timer_register_expires: 60" in SIPDefault.cnf Is there a way to have these phones register themselves every 60 seconds? Alternatively, can asterisk be made to "remember" its dynamic sip hosts' registration after a restart? Thanks,

G'Day All. So I got the TFTP server all set up -thanks to much help from this list- the 7960 found it and updated to SIP the first firmware P0S30200. What I am now trying to do is upgrate through all the versions, as recommended, to the latest version, P003-07-3-00. I thought this would be accomplished by simply changing the sole line in the OS79XX.TXT file to P0S30203 and reboot the phone.

I have 4 7960's that I am trying to get working but 2 of them will not update to the SIP image on my tftp server like the first ones did. i keep getting the error on the phone 'Defaulting CM to TFTP server' like it isn't seeing the *.bin on the server. are you supposed to have on of those for each phone? would be like cisco et al to do something like that. TIA Jason Kawakami

I have used Grandstream phones for years, and have just started testing a Cisco 7940 (with SIP firmware 7.4). I have found something puzzling and don't know whether it's just a limitation or something I haven't done correctly. The Asterisk server is directly on the Internet with a public IP. The phones are on a private LAN with a NAT router to the Internet. The sip.conf entries for

Hi, I can't upgrade an old 7960 from SCCP 3.0 to SIP 7.5. Could you help ? From http://www.cisco.com/en/US/tech/tk652/tk701/technologies_tech_note09186a0080094584.shtml#sccptosip2, I got the following: 1. Copy the desired binary image from Cisco.com to the root directory of the TFTP server. 2. Specify the image in the configuration file image parameter for the protocol