similar to: Xlite dont ring on Asterisk

Hi, I've got an Asterisk box with grandstream and xlite clients on it. No here's the thing: - I grey out all the codecs on the Xlite except for GSM - I call the Grandstream from the Xlite, the Xlite uses the GSM codec and the Grandstream uses ulaw, with Asterisk doing the conversion, everything fine - I call the Xlite from the Grandstrea, the Xlite ends up using the ulaw codec as

Dear all, I have tried to run an asterisk instance together with XLite on a single machine (a PowerBook). The intent is to take advantage of IAX connections to easily cross NATs while traveling. While the IAX setup proved 'easy', just having to fiddle a little with working configs at both sides, I did not succeed so far in getting XLite to connect to the local Asterisk server, AND be

I have a bunch of road warriors who I've set up with Xlite clients. Unfortunately the sound quality has been intermittent at best. Sometimes it's great other times completely unusable. When it's bad one usually hears harsh static when the other party speaks or their voice gets "clipped" to static if they speak too loudly. Many of these users have migrated to Skype ? much

Hi, I'm wondering if anyone has experienced an issue with the XLite softphone and asterisk accepting dtmf? I can listen to my voicemail perfectly from my hardphone. However when I dial the voicemail number from my XLite softphone and enter the password at the voicemail prompt, an error appears vm-incorrect and I get an "Unable to read password" message on the asterisk console. Has

hi all, was wondering if someone could assist with a slight problem i'm having. I have asterisk setup with extensions 101 to 109 and am using xlite, grandstream budgetone, polycom ip500 and a couple of other phones. the problem is: 1. only the xlite extension (107) can receive calls. 2. all extensions can dial into voicemail and get mwi when msgs are received. 3. when dialing a non-xlite

Dear All, I have downloaded the xlite version 2.0 for windows and I made the following conf in the xlite itself as the document suggested in order to make it work with Asterisk but still it doesn't work as a matter of fact when I tried to make a tcp dump I can see no packets going between the windows client and the Asterisk server at all, here is the my conf on the xlite itself: in the

I am using the latest xlite phone to connect to the latest version of asterisk (20040727). When I try to make a call the xlite phone tells me "Call not approved". I used the configuration options that were listed on the wiki. The context in the sip.conf file is "from-sip". I have a matching context listed in the extensions.conf file. The phone is able to register

Lets presume that my both software are open. Xlute and Eyebeam But I want my calls from Asterisk to land only on Eyebeam and Not on xlite. How to set it ? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090129/4011be6c/attachment.htm

What's the secret to getting sound through Xlite? The SIP messages all look OK to me, but the sound isn't coming through. It was trying to use GSM, so I searched the archive and tried: disallow=gsm allow=ulaw Now it says that it's using ULAW but I still get no sound in either direction. Phil Skuse (MBJEJPIEUI) <phil.skuse@vicorp.com>

Has anyone managed to get these two phones to make a video call to each other ? If so, care to share how the hell you managed ? the GXV is at the latest firmware, and xlite the latest download Asterisk 1.4 trunk TIA Julian

Hi, I installed asterisk server in my linux box. I configured a user 1000 using xlite and registered with asterisk server in the same linux box. I configured one more user 1001 in other box and this user also got registered with asterisk. But i am facing two issues here. 1. When a call is made from 1001 to 1000 i could see an incoming call blinking but no audio flow is observed. 2. When i made a

Hi, I have an Asterisk box behind a NAT address and also a Xlite 4 soft phone behind a different NAT network. Asterisk -> Nat -> Internet -> Nat -> Softphone. I can register my softphone to the asterisk box ok via SIP but the RTP stream from the asterisk box is addressed to the private non-routeable address of the softphone when I turn on rtp debuging. How can I configure the rtp

-- Attempting native bridge of SIP/1009-3df0 and SIP/101-f8f1 -- Attempting native bridge of SIP/1009-3df0 and SIP/101-f8f1 RFC3389: 5 bytes, level 0... Aug 27 08:32:16 NOTICE[23572]: rtp.c:289 process_rfc3389: RFC3389 support incomplete. Turn off on client if possible Killed Whenever I make a call between extension 101 and 1009 which are both Xten Xlite SIP clients, I get that error and

Hi there, I have tried very hard to setup the x-lite with asterisk, but until now i didn't get sucess. When i start the asterisk in debug mode, i see the message: sip/2.0 401 unauthorized. I know that this problem with authentication. I put in my sip.conf as below. [2203] type=friend username=2203 auth=md5 secret=1234 reinvite=no canreinvite=no dissallow=all allow=gsm

Hi, I have install asterisk and it works fine. But when I use Sjphone and I use Ethereal a Client send "Request:OPTIONS sip:obelix.foo" and Server answer "Status: 404 Not found". But i can talk with two client and asterisk. When I use Xlite i don't have this request it's clean. I don't understand??????????????

I am having a one way audio issue with xlite clients behind NAT. They can connect to the server and make calls but no audio is heard on the other end. my sip conf [general] context=default bindport=5060 bindaddr=0.0.0.0 srvlookup=yes canreinvite=no[tomfmason] type=friend secret=secret callerid="Thomas Johnson" <XXXX> host=dynamic nat=yes canreinvite=no disallow=all allow=gsm

Dear all, I'm setting up a connection via XLITE softphone and asterisk 1.4 but I get the error: *Registration error: 404 Not found* Here my configuration file of asterisk: *[root at dhcppc0 asterisk]# vi sip.conf [gianca] type=friend username=gianca secret=pwd_gianca host=dynamic context=tutorial* *[giusy] type=friend username=giusy secret=pwd_giusy host=dynamic context=tutorial* *[root at

Hi, I have xlite registered with a user. Now i dial an extension say 1500 which has the dial plan as follows. exten==>1500,1,AGI("localhost//hello.agi" So when i dial extenstion 1500 the script hello.agi is invoked which in turn plays a welcome message. I now want to transfer the call now to operator. How can i achieve this???Please help me in this regard as this is very urgent.

Hello, I'm having the following problem when using a headset on XP connected to an on-board Realtek soundcard on an AsusTek M2N68-AM Plus motherboard: - Using any sound recorder (Windows', Audacity, XLite), the level is just too low when speaking at a conversational level, even with the microphone level pumped all the way up (line displayed totally flat in Recorder)

Hello Asteriskians! I have an Asterisk box with a simple HFC card in it and a bunch of people using the Xlite software to connect. The HFC card is connected to an internal extension on our legacy PBX. So far so good. The Xlite clients can call each other, and the internal extensions on the PBX and the Xlites can call each other, no problem. The problem is when using an Xlite to dial an external