similar to: [Asterisk-Dev] Polycom IP 600 XML

Aloha, Did anyone ever get the formating manual for the XML brwoser on the Polycom IP600? Does anyone have a sample? Aloha, Matt

Hi all, I'm researching IP phones for a new office setup. We will need 30 phones. I have read the wiki and the polycom site for the phones, but I still had some questions about real world experience with these phones. -According to the documentation, the 500 series ( and 600, according to a polycom rep ) have built in hubs. Has anybody noticed performance issues in this setup, when

Could someone please direct me (via personal email) to a provider with good prices on Polycom Soundpoint IP 500's with POE cables? I need 14 of them. Thanks, Adam ________________________________ Adam S. Robins Executive Vice President & CIO PHARMACENTRA, LLP 5901B Peachtree Dunwoody Road, Suite 380 Atlanta, GA 30328 Office: 770-395-0088 x34 Fax: 770-395-0989 Mobile:

I found this solution from the web and figured I'd share it because it affects all phones getting input from IIS. Map .gif, .jpg, .css etc (in my case I used .xhtml for the Polycom 601) in IIS under your sites: Properties -> Virtual directory tab-> Configuration -> Application configuration -> Mappings tab. Make ASP DLL [..\inetsrv\asp.dll] to handle these files. This

Ok so I added to my Freepbx config running Asterisk 1.2.4 in extensions_custom.conf ; intercom exten => _7XXX,1,SIPAddHeader(Alert-Info: Auto Answer) exten => _7XXX,2,Dial(SIP/${EXTEN:1},12,Tt) and configured my Polycoms via this page http://www.voip-info.org/wiki/view/Polycom+auto-answer+config for auto answer and that works fine if I dial 7 then the 3 digit extension. No

>From their website, the key difference between the polycom 500 and 600 phones is the number of "lines" they support. What does this mean in terms of asterisk? Do I have to have a seperate extension for each of these lines or ? Also, slightly off-topic, how does the 500 POE "optional" cable work? Is this similar to have a power box on your desk, or is just a differently

Hello, I am looking at the Polycom phones. The ip600 has a very nice screen, is that the only real advantage over the ip500 and ip300.. Is it worth the extra dollars? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au <blocked::mailto:Michael@ITMedic.com.au> http://www.ITMedic.com.au

Hello everyone, Please forgive the exclamation points but I have been battling this one off and on for about four days now. Sorry for the cross post. It all started with a box of IP 501s. I contacted my reseller and obtained the latest BootRom and SIP firmware. Unzipped, configured, copied over to my FTP server (running AstLinux, of course). The phone booted, so far so good. Updated

I am having a problem with Polycom auto-answer. I have the auto-answer working between PhoneA and PhoneB, but when I try to use the intercom between more then one phone I start having problems. PhoneA dials *3 which calls PhoneB, PhoneC, and PhoneD. All the phones ring, but only one will pick up, the rest will hang up and I get this error on Asterisk: Got SIP response 500 "Internal Server

Is the main difference between the two the full duplex speaker on the 330? -- Warm Regards, Lee

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

Hi Everyone, I've been asked to determine which phones our organization should go with. And I've narrowed it down to the Polycom IP500 or the Cisco 7940. From my travels through google, it's hard to find a definitive comparison of the two phones. So I thought I would ask the people that have probably used both. From what I can tell, the only major benefit the Cisco has over the

Has anyone been succesful pushing a VLAN setting to a Polycom phone via DHCP? I can push the boot server via option 66 but that is about it. I have set it for 'fixed' and tried many different option numbers with a couple differnet DHCP servers. SIP firmware 1.3.4 or 1.4.1 doesn't make a difference. Aloha, Matt

Hi, Has anyone tried to use cdp to push the voice vlan tag to polycom phones? The document says that it is supported, but I can't make it work. Thanks, Richard

I just received my first polycom 501, tried my best to follow all of the documentation and configs on the wiki ( though some conflicted in which case i tried both ways ), and at the end of the day can not connect my phone to asterisk. My Questsions: does the wiki information apply to the 501's? The images and config files at freedomphones, are those supposed to work with the 501? Has anyone

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

i have ordered 500s from tritechcoa.com several times over the past 4 months. great service and delivery, and the prices are lowish, only problem is, they add a $20 handling fee per phone, on top of phone price, and shipping, making the lower price not as good -----Original Message----- From: Mojo with Horan & Company, LLC [mailto:mojo@horanappraisals.com] Sent: Friday, July 15, 2005 12:01

I'm trying to develop a company phone list accessible via the minibrowser feature on the phone. The pertinent section of ipmid.cfg is as follows: <microbrowser mb.proxy=""> <idleDisplay mb.idleDisplay.home="http://server/polycom/index.html" mb.idleDisplay.refresh="300"/> <main

Could any of you provide me information on a good Polycom phone dealers to utilize. One who provides firmwares ..etc Thank you! Kenny ______________________________________________________ Click here to donate to the Hurricane Katrina relief effort. http://store.yahoo.com/redcross-donate3/

I have just spent the morning playing around with a Polycom IP600's microbrowser. Everything is working pretty well. In answer to the question of what type of XML it runs, it appears to be more or less XHTML-compliant. I have created a basic set of web pages allowing users to clock in and out against our MySQL timeclock system, running a PHP back-end. It's running like a champ.