similar to: IAX2 (Variables)

at least 4 me. Anyone knows what are the variables in an inbound IAX2 call who reflect the actual codec and DNID, DNIS, original peer description, I'm only able to see it during an iax debug Timestamp: 00003ms SCall: 00001 DCall: 00000 [66.98.146.34:5036] VERSION : 2 CALLED NUMBER : 911214686 CALLING NUMBER : asterisk CALLING NAME : asterisk LANGUAGE :

What's the content of your /etc/nsswitch.conf? Am 19. Dezember 2014 14:22:56 MEZ, schrieb Rich Webb <rwebb at zylatech.com>: >Matt, > >Thanks for the reply. I'm not trying to add the "users" group. I'm >trying to add the "Domain Users" group. That is the reason for the \ >in >front of the space. It's translated as a literal. I think

Im did not follow the complete thread, but you can check the following. smb.conf ## map id's outside to domain to tdb files. idmap config *:backend = tdb idmap config *:range = 50001-80000 ## map ids from the domain the range may not overlap ! idmap config DOMAIN:backend = ad idmap config DOMAIN:schema_mode = rfc2307 idmap config DOMAIN:range = 10000-40000 winbind

On 19/12/14 13:22, Rich Webb wrote: > Matt, > > Thanks for the reply. I'm not trying to add the "users" group. I'm > trying to add the "Domain Users" group. That is the reason for the \ in > front of the space. It's translated as a literal. I think I could also > put quotes around it and not have to use the \ and the space. > > The

I just tried that and I got the same error. I think there is some extended acl support that I'm missing somewhere. It's like the setfacl command is not recognizing the AD groups as valid groups. I should also add the following information: This server is built up on CentOS 6.6 Minimal using the Sernet-Samba Enterprise packages. It looks like the binary that is running is

I have a configuration where RTP traffic is going out interface pub0, and coming back into through pub1. I have bindaddr=0.0.0.0 in sip.conf, and a netstat -an shows: udp 0 788 0.0.0.0:5060 0.0.0.0:* which means that Asterisk is listening on all addresses (on all interfaces?). Anyway, when the RTP traffic comes back in on interface pub0, Asterisk does nothing with it. A

Hai Rich, Your output of ipconfig /all Where are these? Primary Dns Suffix . . . . . . . : DNS Suffix Search List. . . . . . : This one is below in the output. Connection-specific DNS Suffix . : Verify above again, if these 3 are all there and set to webb.local Then try this : in you network settings, disable ipv6 Beside ipv6 and the 2 missing outputs, i see the same here on my pc.

On 19/12/14 13:40, Rich Webb wrote: > Running CentOS 6.6 > Using the Sernet Enterprise packages - sernet-samba-ad. > > Just tried: > > getent group "Domain Users" > getent group DOMAIN\\Domain\ Users > > and neither command returned any entries. > > Rich > > -----Original Message----- > From: samba-bounces at lists.samba.org >

Would someone be so kind as to explain the differences between the sernet packages? Either that or point me to an internet resource that would explain it? What I'm trying to figure out is what packages to use to set up a full fledged member server in an existing samba4 domain with an existing DC. I want to be able to create a share on this server and then be able to manage it's

Sorry, this is off topic to asterisk itself, but is about the list server. I had a power failure lastnight at home, where my email server resides, and my network was down for about 20 minutes, that was after 45 minutes of uptime on UPS. Since power was restored, around 9:45 PM EST on 2/16, I have not received a single post from the users, biz, or dev lists. Normally when this has happened

Hello all, For some reason I am not showing registration in SIP. Can anyone give me an idea what can cause this? asterisk1*CLI> sip show registry Host Username Refresh State -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050311/bd3a7577/attachment.htm

Hmmm.... Can't place calls... Can't access website... Neither of the 3 nameservers answer anything... Anyone heard/know something to explain all this?

Is anyone out there using any of the newer linksys phones since Cisco took over? I am more specifically looking at the spa-941 & 942's. Just curious about call quality, programability, and functionality with asterisk. I have read through the literature, but would like some real world feedback. Thanks

Hello list, I use R for microarray analysis. One procedure I use takes a large matrix, and loops through it looking for specific rows, does an operation with them, and outputs a result (single row) as a row of another matrix. The loop goes on about 25000 times. When I run the loop directly from the R console itself, it takes about 3 minutes in my computer. I'm ok with that. Now,

Hi all, With the ability of an easy install using Asterisk@Home, I have decided to give it a try. It is my understanding though, that one cannot add zap fxs ports as extensions using AMP. Is there anyone using Asterisk@Home and have added any extensions as zap fxs channels? Would be interested in how you accomplished this. Robert

can i play quake 3 with wine ??? how can i launch it ??? tkx

Does the MWI feature work with IAX2? I have read where it should but cannot get the indicator to work on any of the IAX softphones that I have tried which have this feature. I even did an IAX debug and did not see where and indication was sent to the phone when it registered. IAX2 registration session: *CLI> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ

Is there a way to hide the callerid on analog line on outgoing calls. Any ideas whether it could be done through configuration, a script or hardware. Thanks; ____________________________________________________ Yahoo! Sports Rekindle the Rivalries. Sign up for Fantasy Football http://football.fantasysports.yahoo.com

Hello All, I saw some coverage of this in the list archive but no one seems to have posted a resolution. I am using Asterisk@Home 0.06 and when I get a call from LiveVoip over IAX I dump it into my IVR. >From there the call is routed to groups based upon input. However, there is no ringback indicated to the IAX caller. Does anyone know how to resolve this problem? Thanks, Wiley

I also have two DCs and I am using them also as filers. Built-In users and groups are normally mapped by idmap.ldb I also got issues with mapping of built-in users. I needed the same idmap.ldb on both of my DCs. I also don't see these groups by hitting getent group. I followed another stragedy: Every new group that will have filesystem access has a name starting with GGF (Group Global File).