similar to: IAX2 (Stupid question)

> -----Original Message----- > From: Robert Webb [mailto:rwebb@ropeguru.com] > Sent: Saturday, March 05, 2005 5:24 PM > To: 'Asterisk Users Mailing List - Non-Commercial > Discussion'; 'leandro_tenorio' > Subject: RE: [Asterisk-Users] IAX2 (Variables) > > > > > -----Original Message----- > > From: asterisk-users-bounces@lists.digium.com

I received this before, and it is because you are using the wrong context in the iax.conf. For example: The context must match the username in the register statement. Iax.conf... register => username:secret@iax.host.net [username] type=friend context=iax-in user=username secret=secret auth=plaintext host=iax.hust.net ----------------------------------------------------------------

I've looked around briefly for what options are available for encrypting the media stream using asterisk. I did not see any SRTP support, and it looks like there is some initial work on iax2 encryption, but whether it works is still open for question I guess. I'm also curious of other solutions that could be bolted onto the front end of asterisk to provide encryption, and are there

Hello list, I use R for microarray analysis. One procedure I use takes a large matrix, and loops through it looking for specific rows, does an operation with them, and outputs a result (single row) as a row of another matrix. The loop goes on about 25000 times. When I run the loop directly from the R console itself, it takes about 3 minutes in my computer. I'm ok with that. Now,

can i play quake 3 with wine ??? how can i launch it ??? tkx

While I don't know anything about Box's M test, I googled around and found a Matlab M-file that computes it. Below is my straight-forward translation of the code, without knowing Matlab or the formula (and done in a few minutes). I hope this demonstrates one of Prof. Ripley's point: If you really want to shoot yourself in the foot, you can probably program R to do that for you. [BTW:

Hi all, I am trying to connect to a softphone application using an Iax channel on Asterisk 1.4.30. I can do outbound calls, from softphone to asterisk, but not inbound from asterisk to softphone. I get the following Debug: ---------------------------------------------------------------------- ---------------------------------------------------------------------- Tx-Frame Retry[000] -- OSeqno:

I'vce got three Asterisk systems here that I'd like to be able to place calls between with IAX. As usual, I've spent several hours playing with it, really getting nowhere. Asterisk is so mentally draining. Each system, pbx1, pbx2, pbx3, should be able to connect to every other. Do I need separate user/peers or can I combine them into a single user=friend for each system? if I place a

I am using Teliax to terminate my calls, and I have 3 licenses' for g729 from Digium. "show translations" verifies that the registration took place. When I place a call, having "allow=g729" as the only allow option in iax.conf, I get the following error: WARNING[361]: chan_iax2.c:6017 socket_read: Call rejected by 208.139.204.228: Unable to negotiate codec If I place a

Hi, I have two asterisk servers and I want to make these servers call each other as they were internal. I have succeeded in one way. Server B can call Server A without problem, but Server A cannot call Server B. Here's the iax configuration of servers Server A: ================== [ipek] auth=rsa context=from-internal host=XXX.XXX.XXX.XXX inkeys=ipek outkey=odtu peercontext=from-internal

Hallo Did you allow udp outgoing on 4569 as well.. i found udp bit different than tcp when comming to firewalls liaan ----- Original Message ----- From: "Bartosz Wegrzyn - asterisk" <junk@lexon.ws> To: <timebandit001@gmail.com>; "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Monday, February 21, 2005 12:29

Hi, I have two Asterisks identically installed on two computers. One of them is directly connected to the Internet, the other one through a NAT router (Netgear MR314). On the one behind the router I have an X100P card installed for PSTN connections. In the local LAN of each PBX they are several hardware IP phones (Cisco 7960 and 7940 with SIP images, firmware image P0S3-04-4-00.bin). I have

Hi Everyone, I have two servers as the following that are trunked with each other via IAX2 trunk: Server A: Asterisk 1.4.21.2 (Elastix Flavor) Server B (IP # 72.72.72.72): Asterisk 1.6.2.0 (Vanilla) Server B can place calls to Server A but when trying to place calls from Server A to Server B this is what I am getting:

Hello I am still having problems with IAXTELL and FWD configuration. I get the following when I dial 17009965342 which is set as an example to dial to FWD people. 1+700+99+ 5 digit number. I have placed XXXXX where my passwords are. CLI> Executing Dial("Zap/14-1", "IAX/abatista:xxxxxx@iaxtel.com/917009965342@iaxtel") in new stack -- Calling using options

What settings are people using? I've seen the ones from dslreports but I'm in that lucky group of people that paid the 1 euro just to have it no longer work. Even after I setup a additional account over the weekend it still doesn't work. And, of course, etherreal only shows encrypted traffic so I can't snag any config settings from it. Any assistance? -----Original

Dear Members, I am trying to make call from one Gnophone to another through the local Asterisk Server.All the three systems have local IP Addresses I created two users "sheeba" (extension 600) and "test" (extension 602) in iax.conf file: [sheeba] type=friend auth=plaintext host=dynamic secret=sheeba context=default allow=gsm permit=0.0.0.0/0.0.0.0

Hi, I'm using http://www.portunity.net/ I configured now asterisk with the following setup: iax.conf: register => XXXXXXX:YYYYYYY@iax.iaxport.de [portunity-out] type=friend host=iax.iaxport.de username=XXXXXXX secret=YYYYYY context=incoming-portunity notransfer=yes [guest] type=user context=default ;callerid="Guest IAX User" And in extensions.conf: [default] ;exten =>

Hi, I'm having trouble getting IAX calls through in one direction. On the receiving end I see:- Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: NEW Timestamp: 00014ms SCall: 00001 DCall: 00000 [1.142.164.215:4569] VERSION : 2 CALLED NUMBER : 2003 CALLING NUMBER : dave CALLING NAME : Dave Smith LANGUAGE : en CALLED CONTEXT :

Running Interlinear Scripture Analyzer v2.1.3 prompts the user to install XP support "files for complex script and right-to-left languages" via the control panel for proper display of hebrew. How can such support be installed?? The hebrew fonts have been successfully installed and are functioning correctly. Right-to-left is not working in the ISA2 app. Tkx.

I'm looking for Spain Voice Numbers, anyone know a trustable company that provides them? TKX, Leandro