similar to: Repost: How do I install Skinny support for non sip cisco phones

Does anyone know if the 7912G (which the wiki says can do either sccp or sip) uses the 7940/60 sip firmware? I ask this because the only firmware I can seem to find on TAC for the 7912G is sccp, no sip...if it takes it's own firmware and doesn't use 7940/60 firmware, can someone point me to the right location for it? Thanks, Marty Mastera M3 Resources marty@m3resources.com Phone:

I would like to hear stories from people using TAPI, CTI or CallerID software with Asterisk. What are you guys using, setup examples, etc. Has anybody sucessfully integrated SugarCRM with Asterisk and how did you do it. Are you running callerid software? Did you stumble into problems like using tapi and callerid software returned both the callerid and calledid? Hope you can help me out with

I would like to have asterisk pass along the caller ID phone number to a database server on a my local network (the same network that the * server resides on ) so that our customer service app. can pull up customer data automatially. Asterisk passes along caller ID to the phones fine, can someone tell me how to make it pass this info to my database server? Any suggestions would be greatly

Hi all, I've been searching the wiki and google for a couple of days now but cannot find any reference to a timing source on OpenBSD. I have * CVS-v1-0-02/15/05-21:54:52 (I always do a cvs -q up -Pd before compiling) running like a charm on OpenBSD 3.6 Now I want to setup some IAX trunks to work and 3 friends and some meetme rooms but it looks like I need a zaptel timing source. Anyone can

Hi, Does anyone have any experience with a Cisco 7961 + 7914 Operator Console setup and speeddials/BLF on Asterisk 1.4? Would appreciate feedback if this works reliably. I have a 7961 on skinny registering on an 1.4.19 box with chan_sccp and speeddials work fine so that part seems ok. I have no experience with the BLF part. >From googling around it seems that BLF on the 7914 only works with

Hi, I read a lot about US providers that can terminate a PSTN number for you and offer IAX or SIP connectivity. Does anyone know such a company in The Netherlands ? I read about Unet. Anyone with experience with them ? Any information is welcome. -- Michiel van Baak http://lunteren.vanbaak.info michiel@vanbaak.info GnuPG key: http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x7E0B9A2D

Hi! I would like to have feedback on wireless (wifi / 802.11b) IP phone to use with Asterisk PBX. Can you sugest model, The best and also the worst to use. Thanks, eric.

Hi all, My BRIstuffed 0.2.0-RC7k is running fine on my debian box for voice calls over ISDN2. Now I want to implement receiving incoming faxes into my setup so I did a google and some reading on the wiki. I got the spandsp 0.0.2pre10 package compiled and installed, patched asterisk's apps makefile and compiled * again. This all worked out fine. When integrating the RxFax into my dialplan the

Hi all, I registered a SIP account at budgetphone.nl/talkin2ya.nl Receiving calls works like a charm, I even redirected my normal PSTN number to the number I got from them so everything ends up in my * server. Before I ask them to take over my normal phone number I wanted to test all of it, so I ordered some calling minutes to test. Now I cannot get outbound calling to work with them. Anyone here

I am looking at setting up redundant servers for my client and I know the first step in creating an auto fall back would be to have the FQDN set up in such a way that it points to both of the server IP addresses, but, how can I make it so that the phones will (with minimal delay) authenticate with tha backup server in the event of a primary server failure? Thanks, Dan

Has anyone any experience of the above. Key feature for me is tracking incoming and outgoing emails and linking them to the contact record. Thanks, sorry for the OT ;-)

Hi, Somebody already made call recognition with database access? Depending of call's number, it access a database looking for that number. Where can i find something about this? Thanks in advance Pablo Fernandes

Ok, this is my third help plea for the day, however it's something that has been bugging me for quite some time. To put it quite simply, "Stop now" doesn't. Neither does "Restart Now" Well, ok, if I start *, and then "stop now" it does. However, after a day's calling (2000+ calls from SIP->Zap pri or zap pri->sip), it doesn't. The only way

Hi, I wonder which PRI interface card is most stable and supported for EuroISDN and Asterisk ? Are they stable enough ? Any tips ? Thanks in advance, regards, Rob.

Has anyone tried compiling the zaptel stuff under the 2.6.11 kernel? I get all kinds of errors when doing that. On the 2.6.10 it works fine. This is using cvs. Also, any news on when a 1.2 will be released? Or even available for download? :) -- respectfully, Joseph =============== ---------------------= ********** =

Hello! I'm curently using * with two old Teles PCI card (wich, btw, were hard to install and make good use of) with ISDN4Linux. The sound quality is simply perfect. However both dialing in and out through the ISDN line, there seems to be a _little_ bit of echo that eventually gets on your nerves ! Also the echo seems to get a _little_ bigger after a minute or so into the conversation. Now,

Hello Everybody, This is Bharat here. I am on the way of learning Asterisks, and I just wished to know how I go about if got to write dailplans for outbound calls and inbound calls. If you could provide me with a simple example, I could get thru. Waiting for your response Regards Bharat M. Sarvan -------------- next part

Say there! This is a new Asterisk install on Fedora; I downloaded and installed Asterisk 1.2.1 and it runs fine. I downloaded the 20051217 version of chan_sccp, compiled and it installs ok. When I start Asterisk, it dies on startup at the activation/recognition of the chan_sccp module... A snippit from the startup: Asterisk Dynamic Loader Starting: [res_musiconhold.so] => (Music On Hold

I've added lines like this: speeddial = 123,test speeddial = 260,Bob in the [device] section for my 7921, but the speed dials do NOT appear on the menu (click right from the main screen). Am I missing something obvious here? Thanks MD -------------- next part -------------- An HTML attachment was scrubbed... URL:

hi any one tell me how to make a dialplan my extensions.conf exten => _40XXXXXXXXXXXX,1,Dial(OH323/${EXTEN}) i want to dial to 40XXXXXXXXXXXX number. XXXXXXXXXXXX could be any number like 923335224005 or 92512213248 at the moment when i am trying to dial 40923335224005 asterisk is dialing Executing Dial("OH323/R11429", "OH323/40923335224005") but i want him to dial