similar to: Strange MSN issue with HFC-s

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

hello, i have a problem starting asterisk with one x100p digium and two hfc chipset isdn cards with bri-stuff.0.0.2. "ztcfg -vv" shows me a this info: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03:

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

Hello List, is someone operating a DID /P2P / Anlagenanschluss with more than one HFC-Based ISDN-Card ??? I have now 12 hours of setup-troubles behind me with Colt-Telekom, where we did not get it working with two HFC-based cards. Here the setup: - 2 HFC-ISDN-Cards (the one from Conrad-Electronic) - bri-stuff.0.0.2 (with the asterisk-sources from the download.sh-skript) - two NTBAs from

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi all, I've been batting my head against a brick wall for the best part of the day and still haven't got any further (apart from getting a big headache, that is). I've searched the Wiki and Googled the hours away, but I still can't find supportive documentation. I've just replaced my ISDN Fritz!/chan_capi setup with a HFC/Zap configuration and had the following problems: 1

Hi, I have built another Asterisk box using one ISDN HFC-S card and Bristuff-0.2.0-RC8p. But this time it behaves very strangely. Asterisk simply hangs and in logs I receive something like this: --NOTICE [1197]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 --NOTICE [1197]: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 And when I want to call a ZAP channel I get

I am running * with a Junghanns quadbri that should allow us to integrate our ISDN house telephone system with VOIP. Preferably I would like to run a setup, so that our internal ISDN phones on an S bus are not aware that * is sitting in between. With the configuration below I run into the following problems: 1. On outbound calls, I get the normal rining call progress tone althought the

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi all, I have Asterisk working great for a while now, and until now, only needed to forward calls which originate from one country (Holland, +31). We have a Wildcard TE410P card and configured it in zapata.conf as: switchtype: euroisdn pridialplan: unknown ...etc This was all fine, but now we want to also forward calls to the voice-switch with a calling-number with a different country code.

Hi all, I have a problem setting the MSN for outgoing calls. I'm using a HFC PCI card together with zaptel and bristuff. All my outgoing calls are using the same (first|default|main) MSN. In my zapata.conf I tried different values for pridialplan, prilocaldialplan, nationalprefix, etc but without any success. In my extension.conf I'm setting the MSN with: exten =>

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my