similar to: Outbound calls on a busy Zap/1: BUSY vs. CHANUNAVAIL

I can dial from 601 to a public number. The public number rings. I pickup and hear nothing, while on 601 it keeps ringing. (BTW, is it right to say "ringing" on the active phone?) The *CLI> doesn't show me anything useful: Executing Macro("SIP/601-8238", "dial-pstn|88097880|") in new stack Executing SetGlobalVar("SIP/601-8238",

I got two phones on an ATA-186 (601, 602) and two phones on the TDM22B (603, 604). I have two lines on the TDM22B. I cannot figure out some of the problems: 1. 601 dials via ZAP/3-1 to local phone number at PSTN: ringing pickup on PSTN (empty) still ringing in the phone set 601 2. call from PSTN back: 601 picks up ... everything works !!! No caller id shows up 3. For testing I have only one

Hi I am using Asterisk 1.2 and for the life of me, I am unable to transfer outbound calls (eg calls I initiate from sip extensions). When I press #, nothing happens. Inbound calls transfer fine, but only once per call. The problem happens: - With both software and hardware phones. - With calls going out through the ZAP channel and to internal SIP extensions. - After I have transferred an

I'm still trying to learn some parts of Asterisk, so sorry in advance for the dumb question! How do I set up an extension to dial out to the PSTN through my ZAP interfaces? I want the ability to have a ring group that will ring all of the phones in an office and then ring cell phones if nobody answers. I'm sure this is simple to do but I'm at a loss. I have tried the following

How do you enable call waiting on sip phones? Ive looked and googled and can only find call waiting pstn phones butnot for sip. Is their a way of setting this up within the dailplan?

Hi This is the output from show dialplan dial-sipmnf-sippt-pstn [ Context 'dial-sipmnf-sippt-pstn' created by 'pbx_config' ] 's' => 1. Verbose(1,Dialing ${ARG1} on mnf pt pstn) [pbx_config] 2. Dial(SIP/${ARG1}@${SIPMNF},${ARG2},${OUTBDIAL}) [pbx_config] 3. Set(GLOBAL(FOUNDME)=${DIALSTATUS}) [pbx_config]

Hi I am in the process of move a company from pstn to an asterisk setup. They had 2 pstn lines - only really needed a max of 2 previously. Now I have installed a tdm410 to handle the cross over from pabx to voip handset. this has been done, the tdm is now just used to provide a backup pstn line - only used as a last resort for outgoing calls - as its shared with a fax line. I use 2 voip

What would it do if you exten => h,1,ResetCDR(w) exten => h,2,NoCDR() exten => h,3,DEADAGI(get-unqiueid.php) I have not tried it but in theory it should write the first CDR and then kill the write of the second NO ANSWER CDR. Let me know if it works for you as I may need to do it on some of my h exten code as well. Bryant ---------------------------------------- From:

I've got a setup where we have 100 DID's. Our default dialplan has one line that calls a macro: exten => _22XX,1,Macro(STDEXT,${EXTEN}) The macro is pretty basic: [macro-STDEXT] exten => s,1,NoOp exten => s,2,Dial(SIP/${ARG1},15,Tt) exten => s,3,Goto(s-${DIALSTATUS},1) exten => s-NOANSWER,1,Voicemail(${ARG1}|u) exten => s-NOANSWER,n,Hangup exten =>

Greetings to all, I ma having a problem with channel variables on a couple of our Asterisk boxes. Here is the setup. Asterisk on customer's site (1.2.5), using IAX to our external GW (1.2.5), IAX to PSTN GW (1.0.10), E1/PRI to PSTN. On the External GW, we also have an IAX trunk to a VOIP provider if for some reason the E1 is down. If the DIALSTATUS is CHANUNAVAIL, which should be

Just throwing this out here, hopefully someone can tell me why. *CLI> show version Asterisk CVS-HEAD-11/17/04-10:16:38 built by root@wanderer on a i686 running Linux Zap/g1 is pri_cpe to Bell Canada 5551234 is a normal POTS line I have busied out (handset offhook) exten => 1234,1,Dial(Zap/g1/5551234,,g) exten => 1234,n,NoOp(HANGUPCAUSE is ${HANGUPCAUSE} and DIALSTATUS is

I encountered this strange problem which is I can call into Asterisk box but I cannot call out. I was successful before using exactly the same euroISDN line but with TE110 and different versions of Asterisk. This time, I am using: . TE410 . Asterisk 1.4.13 . Zaptel 1.4.6 . Libpri 1.4.2 1) I put the following into extensions.conf to get to the outside line exten => 0,1,Dial(Zap/1) 2)

Regarding this I've read the specs linked to in detail, but I can find no mention anywhere of any change that implies or states that no ring time will be recorded anymore in Asterisk 13 and that all times in start and answer columns will now be equal for all calls. Can this be because I nowhere use the Answer() application in my dialplan when dialing out? -----Original Message----- From:

hi ppl :D my configuration is as follows, i run (let's call it machine 2) debian etch 4.0 and asterisk 1.2, i use voiceone (www.voiceone.it) as an interface to manage asterisk, I have a grandstream/handytone 486 as a sip device, no PSTN line or anything like that all SIP only. I have a machine (machine 1), which functions as my router and machine 2 and sip device are behind it, grandstream box

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

Hello, i have a simple but annoying problem. I have the following entry in /etc/asterisk/externsions.conf file: ---<Cut Here>--- exten => 10100,1,Wait(4) exten => 10100,2,Playback(transfer,noanswer) exten => 10100,3,Dial(${PHONE30},30,t) exten => 10100,4,Background(extension) exten => 10100,5,Background(is-curntly-unavail) exten => 10100,6,Voicemail(9999) exten =>

Skipped content of type multipart/alternative-------------- next part -------------- ############ # amd BOX # ############ ## Step 1 ## Bob(ext. 6202) place a remote IAX2 call to the operator (ext. 6302) ## Reminder : _62XX are register on 'amd' and _63XX on 'dell' -- Executing SetGroup("SIP/6202-d193", "IAX") in new stack -- Executing

Hello, this is an example extensions.conf. [default] exten => 500,1,Answer exten => 8,1,SetGlobalVar(firstdigit=8) exten => 8,2,Goto(process,s,1) exten => 9,1,SetGlobalVar(firstdigit=9) exten => 9,2,Goto(process,s,1) I call extension 500 and send dtmf digit 9. This is printed to the CLI: -- Executing Answer("Zap/20-1", "") in new stack -- Accepting

Helo List, First I would like to apologize for my bad spelling as well as that I did not search the wiki first. I only have email access at the moment. I am having trouble setting both variables and global variables thru an extension. I am using Asterisk 1.2.4 with Ztdummy on CentOS 3.4 with an Xlite softphone. I have two xlite phones on diffent computers. One logs in as xlite1 and the other as

Hi guys Ive been trying to get this to work for ages now, basicaly im trying to do if ${woteva} = "" (nothing), or its none existenant then do label 1, else label 2. for my last called function, so it will play a different message if theres no last call in the system or it was anonymous. ive tried exten => 1000,1,GotoIf($[${last-call${CALLERIDNUM}} = ""]?4:5) and heaps of