similar to: IAX2 Bandwidth Study

2003-06-28 Bandwidth Study - John Todd (jtodd @loligo.com) Purpose: ------------- To obtain a better chart of actual bandwidth usage per codec as seen "on-the-wire" when using IAX2 trunking between two Asterisk telephony servers. Discussion: ------------- Past threads on the asterisk-dev and asterisk-users lists have indicated that the optimal way to save bandwidth on

Hi all, I'm using VOIPJET to make international calls with an IAX2 connection between my local asterisk server and their server(s). At times I seem to have a problem if 5 or more international calls are made at once - I'm on a 1024kbps download and 256kbps upload DSL line (only the asterisk server uses this DSL line). Today I switched the codec from ulaw to ilbc in an attempt to lower

Hi, I have several users on the lanside each allocated separate IP addresses. I need to allocate th traffic to each IP addresses certain portion of total uplink. Say, 192.168.0.2 rate 128kbps, ceil 128kbps. 192.168.0.3 rate 65kbps, ceil 128kbps 129.168.0.4 rate 64kbps, ceil 64kbps. and so on.... Also, for each user i would like to prioritize the traffic within the allocated bandwidth. say for

The reimplemented APIs are: * list_devices * list_partitions * part_to_dev * part_to_partnum * is_whole_device --- daemon/Makefile.am | 2 + daemon/daemon.h | 3 - daemon/devsparts.c | 257 ---------------------------------------------- daemon/devsparts.ml | 109 ++++++++++++++++++++ daemon/devsparts.mli | 25 +++++ daemon/guestfsd.c | 75

This patch adds a simple callback framework. Modified loadfile and floadfile to look for callbacks and call them if present Supports multiple callbacks Modified com32/modules/linux.c to demonstrate functionality (it's a little more complicated than it should be just to demonstrate multiple callbacks). Add progress argument to display a percentage indicator when loading. Example boot:

Hi all - We have several servers working just fine with IAX2 w/o trunk mode. We are trying to setup trunk mode to save bandwidth, but we can not achieve the savings with our current configuration (see below). When we place a call between * boxes A & B it works fine, but the command 'iax2 trunk debug' shows no activity for the trunk mode (1 peer, 0 calls). Anyone who has

christophe.guerin@etud.univ-pau.fr wrote: > > * Enough bandwidth to run the server. If you want to broadcast to 100 > listeners at 24kbps, you'll need about 24kbps*100 = 2,400kbps = 2.4Mbps > of bandwidth. That's about 2 T1 lines worth of bandwidth. Trying to > push 100 128kbps listeners down your 768kbps cable modem isn't going > to work :) It

This patch modifies the simple menu com32 program to include integrated load progress. It also adds new options to the simple menu configuration MENU LOADMSG -- allows the user to specify the text to display when loading MENU LOADMSGROW -- controls where the text is written Example configuration: MENU LOADMSG Booting MENU LOADMSGROW 25 It works with my setup, please let me know if you find

My previous message (http://mailman.ds9a.nl/pipermail/lartc/2004q2/012285.html) didn''t generate any replies, so I thought I''d try posting what I''ve done trying to solve my own problem, in hopes that someone will take pity and show me if/where I''m going wrong. Just to recap, I''m trying to accomplish this on my server, which streams RealAudio files

Hi, I've just joined the list. Thanks Jean-Marc and other contributors for your efforts with Speex. Anyway - I've been hired by a local firm to investigate, write-code-as-required and generally help them get the maximum bang-for-the-byte for VOIP traffic on the hyperexpensive Internet bandwidth going out of South Africa. I started the process by doing some methodical measurements and

Greetings, Scenario: Centos box with eth1 (10.0.0.0/24) and eth0 (192.168.0.0/24) segment on eth0 has access to full bandwidth of uplink Both are on 100mbps switches Requirements: bandwith on segment on eth1 needs to be throttled to different speeds - say 32, 64, 128kbps and the such. Required for application performance testing purposes. As usual my girlfriend google is very verbose.

I am curious if anyone has had problems trunking iax2 with 100+ concurrent calls. I am planning on testing this out tomorrow, however I wanted to know if anyone else has had a problem with this prior to my test so I know what to look for if anything is known and what resolutions have been found if there are any known problems. Specifically I am doing this on fbsd 6 with asterisk 1.2.4 using

Hello. I have just started using iproute2 commands, and I am having a go at making bittorrent use the same bandwidth for upload as for download. I am stuck I think in understanding speeds I connect to the internet through a router modem which gets the real IP and assigns me a private ip through dhcp. So this router can handle a private network, and route it to the internet, pressumably with nat.

Hi all Iam trying to implement "route add " using netlink. The changes are not reflected in the routing table. I have given my code and screen shots of the routing tables. Can anybody tell me is there any mistake iam making in defining the fields . or any other mistake iam commiting thanxs viji //////////////////////////////////// CODE

> On Dec 9, 2015, at 1:56 PM, Chris Bieneman via llvm-dev <llvm-dev at lists.llvm.org> wrote: > > Not sure, but my guess is that the ocaml documents targets aren’t being included in the ALL target, which is resulting in them not being built before the install action. I think you're right. Running "make ocaml_doc" then rerunning "make install" completed the

Hi, I have a newbie question, and a not-so-newbie one. I've just found out about Ogg, and I haven't been able to find a clear answer in the many webpages this proyect has (btw, why not create just one site instead of vorbis.com, ogg-vorbis.com...). The question is, does Ogg use perceptual coding, like mp3 does? And if so, would it be possible to build an encoder in such a way as to

hi, I want to know just enter a string value entering a numeric value is make with the function scan () or scan (nmax = ..) but it does not work for string my goal is to enter three string: name and surname and date of birth I try with this code but it shows me errors print ("enter the name") name <- scan (nmax = 1) print ("enter the first name") firstName <- scan

Has anyone noticed that the --bwlimit doesn't really work? I have MRTG stats happening, and on a 128Kbps circuit, an rsync with the following syntax takes up the whole line. $ rsync -avz -e ssh localfiles.tar.gz user@remote:/path/to/file/arch Any ideas? It's on an OpenBSD box going to a FreeBSD box. Both are 2.4.6. -#0

There is a need for communication channel between host and various agents that are running inside a VM guest. The channel will be used for statistic gathering, logging, cut & paste, host screen resolution changes notifications, guest configuration etc. It is undesirable to use TCP/IP for this purpose since network connectivity may not exist between host and guest and if it exists the traffic

There is a need for communication channel between host and various agents that are running inside a VM guest. The channel will be used for statistic gathering, logging, cut & paste, host screen resolution changes notifications, guest configuration etc. It is undesirable to use TCP/IP for this purpose since network connectivity may not exist between host and guest and if it exists the traffic