similar to: autoAnswer and autoAnswerLogin?

My colleague left our company, then I have to manage all our phones lines and asterisk: please, apologize me because I'm 'absolute beginner' about voip/asterisk!! Well... all seems work fine; we have some queues and some agents; the "music on hold" works fine when the agent press the hold button on the phone (thomson); the agents have the 'autoanwser' flag

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Is there a linux sip or iax phone that will autoanswer and connect to the console or soundcard? I found linphonec but it does not autoanswer from what I can tell. Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050916/8bc76bbb/attachment.htm

My teeth are on edge after this one. A couple of perfectly good hours of my life, and I still don't know what's going on. . . . The extensions.conf.sample that comes with the current SVN trunk has this line, in an example that shows how to use ChanIsAvail: exten => s,n,GoToIf([${AVAILSTATUS} = "1"]?autoanswer:fail) I couldn't get this to work unless I surrounded the

Ladies, Gentlemen We are experiencing an unusual problem in our asterisk 1.4.34.. We are attempting to determine if channels are in use before paging to them. This works correctly, as in it pages the phone.. however, we see the error message below on the console... after googling, we discovered limited information regarding the issue... -- Executing [NPANXX7298 at from-pstn:1]

Hello As far as ive understood, you can just write Exten => s,n,GotoIf([${AVAILSTATUS} = 1]?autoanswer:fail) ${AVAILSTATUS} would return 1, and "${AVAILSTATUS}" would return "1" Jon -----Oprindelig meddelelse----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne af Brian Capouch Sendt: 27. juni 2006 09:10 Til:

Since 1.4 ALERT_INFO variable has been deprecated. I used to send this via AMI: Action: Originate Channel: Sip/1234 Application: AgentLogin Data: 1234 Variable: _ALERT_INFO=info=alert-autoanswer Callerid: AutoLogin[1234] In order to send an autologin and autoanswer call to the agent 1234 on an Aastra phone at extension 1234. (just for example). Now in * 1.4 with ALERT_INFO deprecated I

Matteo Brancaleoni wrote: >Hi. > >I'm experiencing a strange issue with *. >I have a dev kit, aka a T100P + a zhone cb. > >Sometimes, on certains phones (on the fxo ports >of the cb) , when the phone rings, * detect >it as answered after the first ring, even >if no one is at the phone! > >The result is that on the other party (which >called the phone) hears

I'm afraid I already know the answer because I've done a lot of searching, but does anyone know of a softphone that supports a central phone book and paging (like the sip autoanswer option of some hardphones) Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910) 285-7200 david at safedatausa.com

Hello, I am just getting started with res_config and ODBC. I have MySQL all setup and am filling it with my data. Everything seems very straight forward. One thing catches me so far: 1) How are register lines in sip.conf and iax.conf represented? i.e. register=> username:password@fwd.pulver.com/700 insert into ast_config (filename,category,var_name,var_val)

Check your FW-1 tracker and see if any sip packets are dropped during call initiation. I had this problem and it went away when I upgraded the BT's firmware to the latest (16). Beware, though, that people on the list claim that this firmware breaks functionality of the message button and autoanswer. I haven't checked this yet, cause I can't afford to go back a version. I prefer a

But where do can you get this later firmware from? I'm still on 1.0.0.78 on my 480i. Regards Lee -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Peter Passchier Sent: 05 August 2005 00:04 To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] AASTRA 480i Firmware 1.2.0.162 SIP ALERT_INFOproblems

Hello-- What I'd like to do: Use IAX softphones running on computers, in Auto-answer mode, with sound going to speakers, as a sort of public announcement system. What isn't working: Well, my first experiment was to set up the MeetMe system described on the Wiki... This works fine for voice announcements. You pick up a phone, dial the right extension, and an agi is fired up to put files

I'm replacing a Merlin for a client and they have a PagePal Intercom that I would like to reuse. Here is what I know about it: It has a screw-down wires that goto rj-11 (This was told to me over the phone) that went into one of the Merlin ports. I tried bring it up with fxo_ks and fxo_ls (assuming it was analog and autoanswered) but no luck. I would be happy to replace if anyone knows of

Is there anyway to force an autopickup on a cisco 7940 / 60 from the dialplan ? My problem is that I am originating a call from the AMI, with the internal user being called first, and then connecting to external user. However, sometimes the internal user doesn't pick up the phone, so the call is never placed. I need to know the results of the call so I need to be able to either a) get

Hello All, I've asked this on the asterisk-dev list, so sorry for cross-posting. So far I'm not sure how to accomplish this without looking at the source code or looking at some other way to get around this issue. I'm trying to have an automated call to an Aastra SIP phone and have the call auto-answeredby the phone. I know that a SIP call placed to the phone can be auto-answered if

iaxComm is an Open Source softphone for the Asterisk PBX. iaxComm compiles and runs on Win32, Linux and Mac OS X (Panther) systems. Recent Changes: * Improved jitterbuffer code * Steve Underwood's Packet Loss Concealment Code Features Include: * iLBC support * GSM support * speex support * ulaw and alaw support * Blind Transfer. * Custom Ringtones per

A friend pointed out this url http://www.cisco.com/univercd/cc/td/doc/pcat/clmn32.htm where it lists intercom/auto-answer as being a feature in Cisco Call Manager (which as I understand it, uses SIP predominately for handsets). I've come across comment somewhere that intercom isn't supported in the SIP spec. Does anyone know if the apparent capability of Intercom being available in SIP

On a Cisco 7960 Auto Answer is only configurable using the phone (not via TFTP), does anybody know if it is possible using sip notify or any other way but walking over to the phone?