similar to: Grandstream stops working after "Register Expiration" period has passed (dynamic registration)

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

Hi all, Just wondering if anyone's come across this issue, and what might be a fix for it: We've got several BT-101's deployed, and upgraded to firmware v.1.0.5.16. The phone can do proper supervised transfer, but _only_ once. If the user attempts to transfer a second time, it won't work. any suggestions/hints/tips are welcome.. Flynn

How does one do translation for calls that come in from other pbx's where the incoming caller ID is an internal extension number on their pbx? Eg. when I get a call from Free-World-Dial the CID shows up as "429102" which is essentially their internal extension number sans any routing prefix. To dial the number back I need to dial the extension with FWD's routing prefix

you can not ping that address because ICMP is turned off. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of Deon Rodden Sent: Monday, July 26, 2004 2:22 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Broadvoice problems again Attn: James Greetings, C:\>ping 147.135.8.129 Pinging

Version 1.0.5.23 is now available from http://gs-firmware.gratissip.dk/ Or directly from Grandstream at http://www.grandstream.com/BETATEST/Release-b21p1.0.5.23.zip Release notes doc here http://www.grandstream.com/BETATEST/Release_Note_1.0.5.23.doc while on the matter I just want to extend a note of thanks to Grandstream, I had 2 early handsets of theirs fail recently (about 9 months old)

I've searched for a few days now without finding an answer. The release notes for version 1.0.5.16 of the Grandstream firmware says it supports attended transfer using replace but the docs haven't been updated so I can't work out how to enable it, or whether it should Just Work. I'm currently using the # attended transfer patch for * but would like to get back to using the

Hi All We have Grandstream 102's running ver X.18. When hanging up after a call has been made the grandstream seems not to disconnect the call and when you put the handset down the phone rings only to pick it up and be on the same call. This is happening quite often and gets very irritating. Can anyone help with this? Regards Doug

Hi everybody, Is the only way to use asterisk _not_ as root to change the permission of all the directories where asterisk need to create a file? ("/var/run/", "/var/log/asterisk/messages") any help will be appreciated, Cyprien

Hi, I compiled asterisk and chan_h323 on an Opteron in 64 bit mode. In the h323's Makefile I replaced in line 24 CFLAGS += -march=$(shell uname -m) by CFLAGS += -march=k8 and also tried CFLAGS += -m64 -march=k8 Both solutions do compile, but when starting asterisk, a load error occurs: undefined symbol: _ZN14H323Connection24OnUserInputInlineRFC2833ER15OpalRFC2833Infoi When I grep

Hi All, Last week I started hearing a huge amount of local end echo on incomming calls. I am using a Sipura SPA-3000 as my FXO connected to an SBC POTS line. Echo cancellation is enabled in the SPA firmware. As a test I switched to a Digium X100 card the still lives in my server but the echo was about the same. I have both Polycom IP600 and SNOM 200 phone, which both hear the echo. I'm

-----Original Message----- <snip> Is this possible with asterisk? Anyone have a sample dialplan? -other than the problem outlined below I would try something like S,1,wait(20) S,2,voicemail(uwhatever) S,3,hangup That should ignore the call for 20 seconds and then leave a message in the unavailable greeting for 'whatever' then hangup That leaves another problem -

I had my asterisk configuration working very well with broadvoice, but it stopped working this afternoon. I plugged the Cisco 7960 phone I used for my origional signup (just a few days before they offered generic BYOD) and it works fine. I did notice it seems to do all of its comunication through proxy.broadvoice.com (I used tcpdump). I have never contacted broadvoice about using asterisk

Hello, I am trying latest stable Firmware for GS IP Phone BudgeTone 101 found at http://gs-firmware.gratissip.dk/firmwares/ and the phone doesn't send a register staement (nothing in thertereal log). With the 1.0.3.81 version, the phone register properly. Is ther any know bug with the SW Version? Best regards, Daniel ANDRE -- Daniel ANDRE (mailto:daniel.andre@iris-tech.fr) IRIS

http://yro.slashdot.org/article.pl?sid=04/08/04/2212251&tid=158&tid=95&tid=103 Probably some of you already saw this. Now, beyond discussions regarding the legitimacy of such a ruling (whether they have the legal, moral or whatever right to enforce it), there's the technical aspect. Suppose i provide VoIP services using Asterisk, and i fall under the incidence of the FCC ruling

There is now a peering arrangement between e164.org and FreeWorldDialup which means any and all subscribers on FWD are now easily able to make enum calls by prefixing their call with **164, like wise it's almost as simple to make a call to FWD by hitting 8829990<fwd number> This means that for those of you wanting to send/receive calls to/from FWD subscribers you can now do so, easily

Hello, I have a problem with connecting a Digium X100P card to a Brazilian analog line. Can somebody help me out with this problem? My /etc/zaptel.conf is loadzone=br defaultzone=br fxsks=1 My /etc/asterisk/indications.conf [general] country=br [br] description = Brazil ringcadance = 1000,4000 dial = 425 busy = 425/250,0/250 ring = 425/1000,0/4000 congestion =

In our password settings we have: > samba-tool domain passwordsettings show : Password complexity: on Store plaintext passwords: off : Minimum password age (days): 0 Maximum password age (days): 90 : I don't find any setting for how many days before the expiration to warn users about the pending expiration. On Windows, users seem to get notified about a pending password expiration at

Everytime that I make a call to a Budgetone 101 phone. I always see the following: -- Executing Dial("SIP/1001-bac5", "SIP/1000|20|tT") in new stack -- Called 1000 -- Got SIP response 302 "Moved Temporarily" back from 172.22.5.4 -- SIP/1000-465e is busy I can use X-Lite all the time to make a call without a problem, but any of the budgetone 101 phones

Voicemail works fine for me. Post console output here to let us know what went wrong. Cheers, Dean -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of John Breeden Sent: Friday, March 25, 2005 12:55 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: CAUTION: Re: [Asterisk-Users] grandstream

Hi all of you. I am trying to configure voice mail in asterisk and i am facing problems. I have found following warning message in /var/log/asterisk/messages -------------- No application 'Voicemail' for extension (macro-mainmenu, s, 5) I have configured voice mail accordingly in extention.conf [headoffice] -- ------------ ------------- exten => _63,1,Macro(mainmenu)