similar to: ISDN supplemetary services (Hold, Retrieve, 3PTY) on HFC-8S

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

Hi Guys, I got 2 internal HFC-S[5] (not sure what character this is) internal modem cards yesterday, thought I would get different makes as the one was a named brand, the other not... but anyway... Its picked up by lscpi as a ... "Network Controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)" I'm using kernel 2.6.10, and I saw I must use CAPI. I

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Does any one put a HFC-S card working in nt ptp mode? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100221/ca845019/attachment.htm

I've got an old HFC-S card to play with, and I would like to use it in NT mode. I've a problem only: wiring. I can't fully understand the instructions I was able to find online. Someone can point me to a site which explains the whole procedure clearly (like with some schematics, even in ASCII)? TIA, Simone.

It seems so simple, but I'm having no luck installing a HFC-s ISDN BRI card on *@home 0.5. I probably have to install BRI-stuff from Junghanns.net but that also downloads and installs another copy of * from Digium. I'm not sure if zaphfc has to be installed *before* Asterisk or if it's OK to do this afterwards. I've seen this question before, but: Anyone successfully installed a

Hi, I have built another Asterisk box using one ISDN HFC-S card and Bristuff-0.2.0-RC8p. But this time it behaves very strangely. Asterisk simply hangs and in logs I receive something like this: --NOTICE [1197]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 --NOTICE [1197]: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 And when I want to call a ZAP channel I get

I've been trying to set up incoming faxes using spandsp with a HFC card. Unfortunately, incoming faxes are of very poor quality, the pages are not transferred wholly (sometimes only a bit of a page is transferred etc.). From what I've read, I may have troubles with correct "timing" (and need to set up ztdummy etc.). On the other hand, it is impossible to set ztdummy if one