similar to: IAX/SIP Softphone with G729

Hi, I'm searching for GPLed softphones. I found WengoPhone but actually not available for Asterisk PBX, only for Wengo network. I found Kiax but only for IAX protocol. Did you know a good GPLed softphones which works on Windows ? Thanks Greg -------------- next part -------------- An HTML attachment was scrubbed... URL:

Anyone used the combination above? We are and it sounds like crap. The audio drops out in regular intervals which suggests that someone's g729 isn't doing its job correctly. I'm blameing XTen cause when I make a ulaw call that gets converted to 729 using digium's 729, calls sound fine. Anyone else? Similar experiences? -Matthew --

Hi list! Again Wengo has made changes to their servers that require modifications to * configs. Is there anyone that has the 'new' wengo working with asterisk that could post their configs? Also they switched codecs, now G720a is required to connect. I can only find an (open) G729 codec, is this the same as G729a? Thanks!

Folks! We have purchased G729 and have been testing the codec on mUltiple Gateways. Here is what we have found. Here is the config I have used: ------------------------------- Asterisk Server On Dual Pentium Xeons with 6GB of RAM, running on Fedora Core 2 User1 is in USA on Broadband Cable User2 is in India on 64Kbps ISDN Line User1 using SIPURA SPA 2000 user2 using Xten professsional(X-pro)

Guys, anybody has seen or is using some kind of softphone on any square screen device with WM5? Ive tried sjlabs one and xten for pocket pc and they do work on Wm5 but they are designed for standard screens, anybody using anything on square ones?

Hi, IF i use a sip softphone or a iax softphone with asterisk, i get a lag of about 1 second. The two phones were on 2 different pc's near me. When I speak on one, i hear it on the other after about 1 second. I tried using iaxComm, Xten Xlite, etc. Same. FYI: The codec used was GSM. Using the fxo and fxs interfaces on the digium cards with POTS have no such issues. Any clue where the

Sorry if you see this message repeated twice. I would like to set up hard phones and softphones with the same extension so that when anybody in the company dials an extension, each user's hardphone and softphone will ring at the same time. I've tried setting this up before, but I noticed that the last sip device to register with the same extension is the only one that rings when the

Got two phones here. 1 is Cisco 7960 and other is XTen Pro. Both have 729 capabilities and plenty of licenses on Asterisk. The Cisco phone has and registers/talks with asterisk on an internal IP (* = 10.0.3.10, phone = 10.0.3.151). The SIP peer for this phone is set to NAT=No and has this Codec Order: (g729|ulaw|alaw|gsm|g726). The XTen registers to the Asterisk external/public IP, even when it is

Hi all, I have problem with my Asterisk. I'm using the softphone Xten-Lite. I've removed the SIP client information in sip.conf. The softphone can't register to Asterisk, but it can make outgoing calls. I've tried to add back the SIP client information into the sip.conf, but make a wrong password in the softphone. The registration and outgoing calls are failed as expected.

>I went back to the example system direct from CVS with small >additions to sip.conf and extnsion.conf needed to make one >xten X-Lite phone work. I can dail in and hear the anouncements, >call the demo server at Digium. The audio quality I hear >comming from Asterisk back to X-Lite is good (9 on a 10 scale) >but the sound volume comming from the X-Lite extension is very low

Hey gang, I'm trying to setup the ability to dial a SIP user via their email address. I'm using SJPhone as my tester UA, but most clients will be using XTen Pro. I added an SRV DNS entry into our zone, and it returns: ; <<>> DiG 9.2.1 <<>> SRV _sip._udp.cytelcom.com ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status:

Hello I Installed Asterisk on RedHat 9. I am currently try to configure minimum with two softphone talking to each other over the LAN. I am using X-Lite softphones from xten.com site. I defined 3 phones in sip.conf and also specifies in extensions.conf file. I am able to ring other computer but there is no voice exchange ( i can't hear any think except ring). Here is the portion of sip.conf

All, I have my * box NAT'd with all ports forwarded that are SIP related (based on Wiki). I also have nat=yes, externalip=WAN address of firewall, internalip=LAN network of *. I have my Xten soft phone on a PC which is NAT'd behind firewall with ports forwarded. I have also followed instructions on Wiki for Xten. I can authenticate fine, and sip show peers shows my extension is OK,

hi there! I have a couple phones connected to a sipura ata and if I go into *- IVR, I press options on the regular phones and it all works fine and dandy. then I connect an xten softphone, a new extension in my dialplan, I dial the ivr, * asks me to dial something to go through it, I press keys on xten, but nothing happens, * just times out through as if I did not press anything! is there some

Hi, We have to servers set up in two different networks. We are able to connect calls via IAX and they work perfectly. We do not see caller ID from clients on either side. Our Grandstream phones say Eri and our XTen phones say Asterisk. We did a debug and I am pasting the output from both servers below. We tried setCallerId in several different ways. We see the value get passed to the

Hello list, I'm observing what I believe to be inconsistent behaviour regarding "Newstate" AMI events for the "Ringing" state. As such I come to you asking for experience or advice: am I wrong or should I file a bug ? I present you a short introduction which I feel is relevant; however, if you want to go straight to my technical question, please scroll

Guys. Im writing this because Ive checked the wiki, Xten website and read a lot of docs and still cant figure out a way around the NAT issues. Maybe somebody else can give me some ideas from a fresh perpective. My test setup is this: Asterisk -> 2wire homeportal Firewall -> internet Computer with Xten eyebeam The asterisk box and the computer with xten beam are behind the same

I have d/l the iso (*@home 0.9) , built the * box and followed the directions in the * handbook and http://www.geekgazette.com/index.php?option=com_content&task=view&id=2&Itemi d=26. I created extension 200 and verified that * was running fine. Loaded Xten lite, setup the proxy for local ip (10.0.0.201) per the handbook. After turning off the Norton Firewall protection, I am able to

Sorry, I don't remember who was asking about this, but it seems that if you record a video message that contains the send video start, it will actually fire up the remote receive window. I.E. Previously I was using the recording section of voicemail to create my video IVR's. This meant that when I arrived at the section to record the message, I had already clicked send video in Xten.

Is there any winblows softphone available offering g729 *and* IAX? I couldn't find any http://www.voip-info.org/wiki-VOIP+Phones The best choice should be dIAX, but it is only GSM.