similar to: Athlon 64 for Asterisk?

Hi, Is anyone using mozPhone? If so any feedback you can provide? Thanks, Glenn

Today, We have added INVITE Authentication. This seems to bring a large amount of problems to people in the way since they can't make outbound calls. Here's what needs to be done. You need to add three variables to your peers or friends, username, authuser, and secret. username=<phonenumber> authuser=<phonenumber> secret=<registration password> Dan

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

Hello, I am just curious how many people are hooked up with BroadVoice and have recently been experiencing a lot of dificulty. Joel

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

I am trying to integrate a Nortel Norstar system with an Asterisk service using a TDM04B card (4 fxo). So far everyting works from Asterisk to Nortel. The problem is when someone dials from the Nortel PBX to the Asterisk server. Asterisk answers the call and provides a dialtone (with DISA) but appartently the DTMF tones are not passed to asterisk and the call cannot proceed. This only

Is the Broadvoice service up? I just signed up with them and started receiving calls in no time but could not make calls. And after a few minutes I cannot even place calls. register => [number]:[password]@sip.broadvoice.com [broadvoice] type=peer fromuser=[number] host=proxy.lax.broadvoice.com fromdomain=sip.broadvoice.com context=from-broadvoice dtmfmode=inband any help would be

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

Dear R-users. I eventually bought myself a new computer with the following characteristics: Processor AMD ATHLON 64 DUAL CORE 4000+ (socket AM2) Mother board ASR SK-AM2 2 Ram Corsair Value 1 GB DDR2 800 Mhz Hard Disk WESTERN DIGITAL 160 GB SATA2 8MB I'm a newcomer to the Linux world. I started using it (Ubuntu 7.10 at work and FC4 on laptop) on a regular basis on May. I must say I'm

Dear R-users. I eventually bought myself a new computer with the following characteristics: Processor AMD ATHLON 64 DUAL CORE 4000+ (socket AM2) Mother board ASR SK-AM2 2 Ram Corsair Value 1 GB DDR2 800 Mhz Hard Disk WESTERN DIGITAL 160 GB SATA2 8MB I'm a newcomer to the Linux world. I started using it (Ubuntu 7.10 at work and FC4 on laptop) on a regular basis on May. I must say I'm

I am having a problem with and Asterisk installation where two ports connected to a TDM400 card will have a very loud noise when you try to dial. The server has an OpenVox D110P, a TDM04B and a Xorcom Astribank 8 fxs. It is running Zaptel 1.4.11 and Asterisk 1.4.18. The problem always happens with two ports (34 and 35) which are connected to two GSM gateways. They will work fine for a week

Has anybody here taken a HDD configured with an Opteron system, and then put it into an Athlon/64 and had it work? Are they interchangeable, like an Athlon/32 and a P3/P4? -Ben -- "The best way to predict the future is to invent it." - XEROX PARC slogan, circa 1978

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

I have been using a laptop computer of Pentium III 1.13 Ghz. I heard that AMD's Athlon has excellent floating point capacity. So I bought a Athlon 2200+ laptop yesterday. I expected that new Athlon 2200+ will be twice as fast as the P III 1.13 GB. I ran a R simulation program and the new computer is only 30% faster, in fact slightly slower than a Celeron 1.50 GB laptop. I am very disappointed

Hello, as said in the subject; I am having problems with ifcpu.c32 and ifcpu64.c32 detecting a Athlon II X4 CPU correctly as a 64Bit capable CPU. Ifcpu64.c32 does not detect PAE capabilities, also. Both boot the last (32Bit, non-PAE) entry. On two other Core2-based machines I have here, everything works. Can someone tell me what exactly these modules are looking for? Maybe I can compare that

I have a customer running Asterisk 1.2.13, Zaptel 1.2.11 with a TE110P, a TDM04B and an Astribank-32. They have been complaining that there is echo on calls even when they are IP to IP on the same network. There are 18 Aastra 9133i phones and 30 analog phones connected to the Astribank. I can understand there being a bit of echo on the analog phones, but I do not understand why there would be

I installed FC 2 X86-64 on an Athlon 64 system. I then installed R 2.0.0. It runs fine except when I try to install or update packages using either "install.packages" or "update.packages". I get the following types of errors: gcc -I/usr/lib/R/include -I/usr/local/include -D__NO_MATH_INLINES -mieee-fp -fPIC -O2 -g -pipe -march=i386 -mcpu=i686 -c block.c -o block.o cc1:

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

Hi Friends, I have a problem with my Wine Installation in FC2-Athlon. I was following the PDF File - Configuring Wine Chapter 5 and it says that the "config" file is in ~/.wine/config. I can find the "config" file in the /etc/wine/config. Can you enlighten me on this? Actually, I can run already the "wine winmine.exe" and "wine notepad.exe" Also, I was