similar to: OT: pinout for "standard" telephone headset required.?

> Many thanks Julian. Are you looking for the pinout for a single plug 2.5mm (cellphone) headset or a dual plug 3.5mm (computer) headset? -- Nabeel Jafferali Tel: +1 (416) 628-9342 Toronto +1 (646) 225-7426 New York FWD: 46990 Email/MSN: nabeel<at>jafferali.net

Sorry, I know it's OT, but does anyone know of a relatively inexpensive headset that is compatible with the Cisco 7960? I've tried the headset off Norstar phones, doesn't seem to work with or without the amp. ------------------------------------------------------------------------ | nate carlson | natecars@natecarlson.com | http://www.natecarlson.com | | depriving some poor

I have seen on eBay adapters for Cisco 7940/7960 phones, to use cell phone headsets. They were about 12-15$. I think original manufacturere was at http://www.ciscoheadsetadapter.com. >Started a Wiki page here: > > http://www.voip-info.org/wiki-Cisco+Phone+Headsets > > >Jim > >James H. Thompson >jht at lava.net > > ----- Original Message ----- > From:

Say I had a crossover cable that connected a Mitel SX200 to a TE110P and the pinout was done as such: 1 - 4 2 - 5 5 - 1 4 - 2 (the 5 and 4 are transposed on the left side) Instead of the proper way of: 1 - 4 2 - 5 4 - 1 5 - 2 What would the results be? We have had the former as our cabling for a few months and the connection has been fine. Slip errors here and there. But we have had major

I saw these adapters on eBay. 2.5mm stereo jack to modular RJ-9 jack. I think original site is http://www.ciscoheadsetadapter.com Mike >Nabeel, > I am very interested in what you came up with for a 2.5mm to RJ-10 > adapter. > >I played with every combination I could think of but the best I was able to >come up with had a echo of the far end voice back to the far end.

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

I am trying to test the T1 card in our legacy PBX but the connector to the card is a 15 pin serial cable. I would like to make it myself so I can try this test today. Does anyone have a pinout for it? I just made a T1 RJ-45 loop back to test my TE110P and it tested out fine. I'm trying to resolve some timing issues and a tech from Digium is going to ssh in and walk around my asterisk server

Hi I'm looking for a pinout for the above. Note this has what i'd call RJ45 sockets (or someone smart can correct me). I need to plug into BT (rj13?). And, yes I've googled (glad I'm not chinese) and have tried the suggested, just plug in a 6 connector rj11 and i didnt work atall. On a side note, I cannot beleive that Digium dont have this information on there site, it

Hi guys, just to let u known the pinout for the adapter : Adapter for connect the E1 telco lines on my digium card DB9 RJ45 3 1 8 2 2 4 6 5 Adapter used for connect the Hicom150 traditional PBX on my digium card (cross connection) DB9 RJ45 3 4 8 5 2 1

Hello! How long a DC (samba 4) can be offline without losing the consistency of the data? In the case, how long it is safe I rewire it the network? Regards

Thanks for the info. I have a way to view and change it too? (It would be only the level of knowledge). Regards Em 26-10-2016 05:30, Denis Cardon escreveu: > Hi Carlos, > >> How long a DC (samba 4) can be offline without losing the consistency of >> the data? >> In the case, how long it is safe I rewire it the network? > > by design, tombstone life time (the time

This is Off-Topic for Asterisk, but I wanted to get some feedback on headsets for Cisco 7940/7960 phones. We have about 10-20 people who wants/needs a headset for their phone & was hoping to collect some real-world input. Thanks!!

Hi there! I just recently got a nice new UPS to power most of my computer equipment, and having it working perfectly under NUT. However, I had a perfectly good Powercom Black Night 600AP UPS, which I'm now trying to get to power my internet gateway. Unfortuantly, due to not thinking on my part, I threw away the original serial cable. I have tried a straight - through cable, and the one

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

Hi again, folks. I've been getting feedback from this list and elsewhere that softphones are generally not considered good enough for hardcore business use. Can someone point me to where I can find more detail on this debate? Is the problem that the technology isn't mature, that the load on the computer is too high, or simply that it doesn't work well in a poorly designed

Does it mean we can not dereference the Value variables? Value *val = some operand of an instruction; Value *val2= some operand of another instruction; I am trying to rewire the operand values of an instruction using: *val = *val2; It seems that this is not allowed. Thanks, -- Abid M. Malik ****************************************************** "I have learned silence from the

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also