similar to: chan_capi outgoing msn

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Hello, I'm using asterisk 1.0.7. with a somewhat advanced setup with IAX and CAPI as channels. A call comes in via IAX2 and should be redirected to CAPI. So I wrote the following dialplan: [fromiax] exten => _8XXX,1,Answer exten => _8XXX,2,Dial(CAPI/265:B${EXTEN:1},,r) [fromcapi] exten => 265,1,Answer exten => 265,2,Dial(IAX2/PoC/11@from-lw) exten => 265-BUSY,1,Busy exten

All, before I start, I have read the readme and realise the dial syntax has changed since 3.5.....(and I really wish it hadn't).... anyway can somone please help me round a config issue? Previously I had a capi.caonf as follows. This config allowed me to have multiple MSN's on the same ISDN/Fritz! card under seperate contexts.

Hi, I was trolling through the archive to see if it was possible for asterisk to ignore certain MSNs. I have a AVM Fritz/BRI with two MSNs: 7770001 and 7770002. I would like asterisk (with chan_capi) to ignore 7770001 such that a regular phone on the bus will ring; calls for 7770002 should be picked up by asterisk. I configured msn=7770002 incomingmsn=* within capi.conf and figured this would

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i'm in debian sid 3.1 with kernel 2.6.7, * last cvs & chan_capi 0.3.4b; nt1+ with 2 bri in ptmp (http://www.voip-info.org/tiki-index.php?page=DDI) i tried to install avm c4 following step by step http://www.voip-info.org/tiki-index.php?page=Asterisk%20How%20to%20connect%20with%20CAPI step 1. i compiled capi 2.0 support in kernel

Hi, I can't make outgoing calls with CAPI (passive ISDN Fritz card). See Asterisk error below. Incoming calls and SIP to SIP calls do work. It looks like a msn mismatch in extensions.conf and capi.conf, but I can't find it. Can anyone help me find the problem? Thanks, Rob *CLI> -- Executing Dial("SIP/8112-1be9", "CAPI/356666666:BYEXTENSION") in new stack

Hi I have to PCI AVM cards on asterisk and i want to configure them with chan_capi. But there are some things that need explanation to me. 1. If i have not declared MSNs to my provider am i going to put msn=0 to capi.conf? 2.How do the 'deflate' and 'incomingmsn' parameters be set? 3. Although i have two controllers and i4l load them both, chan_capi installs only one? Is there

Hi there, I searched in mailinglist and in web, but no answer to my problem... Only this post with no answers: http://lists.digium.com/pipermail/asterisk-users/2004-March/038994.html I'm using CVS Asterisk (05/17/04) with chan_capi 0.3.1. (multiple controller support). In my Asterisk-box there are 2 Fritzcards (module for second card compiled with changes on sourcecode found in the web).

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

hello, sometimes my capi_channel stop works - e.g. when i try to call number which does not exist ( typo error ) and i must restart asterisk. following lines appears in the log files : ERROR[393234]: File chan_capi.c, Line 1050 (capi_request): no free channel on controller 1! will continue searching. ERROR[393234]: File chan_capi.c, Line 1050 (capi_request): no free b channel on controller 1!

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

this happened to me on a cvs update, rebuilt a clean chan capi cm and all is well. Greg ________________________________ From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Voicomm User Sent: Monday, September 19, 2005 3:29 AM To: Armin Schindler Cc: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Asterisk ISDN: Problem

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hello, I am using chan_capi and would like * to behave differently depending on the MSN the caller dials. Is there a way to route incoming ISDN calls to different contexts based on the MSN dailled? I have tried something like msn=1234 incomingmsn=1234 context=msn1 msn=4567 incomingmsn=4567 context=msn2 in capi.conf but with no results. Thanks for any hints. -Walter -- Walter Doerr

Hi, I have a problem for install chan_capi My pc: Suse 9.1, with asterisk current stable en cvs I have download http://www.junghanns.net/asterisk/downloads/chan_capi.0.3.5.tar.gz And the path from http://www.levigo.de/VoIP/chan_capi-0.3.5-cvs-HEAD-patch.tar.bz2 And patch the chan_capi # cd chan_capi-0.3.5 # patch -p1 < chan_capi-0.3.5-patch.diff # make /for install My error

Hi all, I am trying to get Capi Dial to use a specific outgoing msn. I can't get it to work. If I make a test call to 0703241494 (same isdn line, just one of the other numbers) I don't get CLID at all. Any ideas? ; use 0703241432 as outgoing msn exten => _070.,1,Dial(CAPI/@0703241432:${EXTEN}|30|r) in capi.conf I have: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8

Hi List! I use Asterisk as a pure voicemailbox at a customers place. Right now, a telephone uses up two msns, one for the telephone itself, and one for the telephones mailbox. If the user is absent, a telephonecall is redirected to the voicemail msn of that users telephone. The Problem is: The PBX supports a too small number of msns, so I can't give every user a voicemailbox. Mailboxes are

Hi all, I have installed a test machine with asterisk in order to try it. I have a problem with capi channel (chan_capi 0.3.4a). When an external call directed to an internal Ip phone is not answered I obtain this warning repeated many times: .... .... Jul 12 16:13:43 WARNING[1209214400]: app_dial.c:302 wait_for_answer: Unable to forward frame Jul 12 16:13:43 WARNING[1209214400]: app_dial.c:302

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have