similar to: error?

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Good day all What is the amount of calls that asterisk can handle,SIP and from/to PSTN -- Thanks Altus Snyman Stormcorp Network Solutions +27 11 8071141 exten 301

Hi folks, In an effort to save bandwidth (our 7905s run over a WAN) we've switched from ulaw to g729a. We purchased 4 licenses from Digium (4 SIP clients, low call volume), and they seem to have been accepted: [codec_g729a.so] => (Annex A/B (floating point) G.729/PCM16 Codec Translator) == G.729 Host-ID: 07:53:aa:d3:e2:f2:bd:cc:27:60:9d:5f:da:eb:5d:e9:6e:09:a1:4e == Found license

Hi, I write to this list, because I didn't find anything on the net. I installed asterisk using bristuff-0.0.2 without any errors, but when I start asterisk with "asterisk -vvvc" I get following error: [codec_ilbc.so] => (iLBC/PCM16 (signed linear) Codec Translator) == Registered translator 'ilbctolin' from format ILBC to SLINR, cost 127 Segmentation fault Removing

hi michael, here are the core dumps. only kphone works when 0.5.5 and * cvs. audiocodes and msn messenger all cause seg faults when calling ccm thru * (or vice-versa) ~kelvin [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing '/etc/asterisk/rtp.conf': Found == Parsing '/etc/asterisk/oh323.conf': Found 0:00.004 OpenH323 Wrapper OpenH323 Wrapper

Good day all I'm just wondering for interest sake I have a box,hostname=myname.co.za,running sendmail If I send mail to someuser@myname.co.za it try to deliver to the box,witch does not have the mail box.How do I tell sendmail that it should send mail to myname.co.za's mailserver. I know how easy it is to change the name but there's a lot of reasons why we can.It is not in the

To me it's a error if I can't complete calls using the ATA configured to use the g726 codec. I just tried it usign a sipura SPA-2000 (preferred codec: G726-32) and I received NOTICES and WARNINGS, but I can't complete a call. On a zap channel: -- Executing Dial("SIP/2007-e4d8", "Zap/1/2217008") in new stack -- Called 1/2217008 -- Zap/1-1 answered

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was

Good day all I added the music on hold entry in vpb.conf and commented out default line in musiconhold.conf. Asterisk starts up with the default mp3 but as soon as I remove it and add my mp3 it just doenst start up and gives a broken pipe error? Please Help or advice Thanks ALtus

Good day all IS there a way to personalise the voicemail message when you leave a message? Thanks Altus

PH> I am setting up a snom 360, and the lights come on OK when the mapped PH> user makes an outgoing call, but when the user takes an incoming call PH> the light does not come on. PH> I do not want to install the bristuff patch if possible. PH> (although I can see that with the devstate command I can make the lights PH> do whatever I want) First, ensure that the 360 has

Good day all Is it possable to set asterisk up as a cdr server for other voip units We got a quintum dx here and its got a option to log to a cdr server on port 9002 Thanks Altus

Good day all We have a quad bri card,installed on fedora core1,downloaded the latest bri-stuff that download asterisk 1.0.3 and zaptel 1.0.3 and libpri 1.0.3 All installed and working.BUT after 5min+ of talking it just drops the calls? Any reason why? Please help Thanks Altus

Is H323 built into the current CVS? If so, could someone give me an idea of a simple config? thanks, darran -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030429/fffec1d1/attachment.htm

Good day all I got my voicemail message working,thanks but now,keep in mind I'm using SIP We have,for example 4 people in our admin department.Each user has its own voicemail so that when their extension is dialed directly and not answered it gos to voicemail. But there is also a option to dial 3 for admin with will dial all 4 number in sequence.This I got working 100% but now I want a

Good day all I got my snom 220 phone so that it displays on the buttons if someone is calling that extension I just added "exten => 403,hint,SIP/403" in my dialplan But These lights only comes on if someone calls that extension,not if that extension is busy are a call is made from that extension Can this be done? Please Help Altus

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

Hi, I have a new phone in our IP phone network: Planet VIP-101T. When calling from that Planet phone to anybody, everthing is fine. But when calling from anybody to that Planet phone, I get a mashine gun noise and the following msg in asterisk log: NOTICE[262161]: File channel.c, Line 1091 (ast_read): Dropping incompatible voice frame on H323:0 of format SLINR since our native format has