similar to: Broadvoice Status Check 11:18pm PST

I've tried everything with the * box after this weekend. I have read every document on the problems people are having with them after this weekend as well, but none of them address my problem. I checked my settings in my sips which I have below as well, I have changed the host file a few times, but this was new to me and I never had modified it before. I have and the same results

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Hello All, I have 4 Broadvoice lines. If I call any of the lines it shows that is coming from the first line. exaple register=XXXXXXXXX1@sip.broadvoice.com:passwd:XXXXXXXXX1@sip.broadvoice.com register=XXXXXXXXX2@sip.broadvoice.com:passwd:XXXXXXXXX2@sip.broadvoice.com register=XXXXXXXXX3@sip.broadvoice.com:passwd:XXXXXXXXX3@sip.broadvoice.com

I'm getting a couple strange things with asterisk on Broadvoice. It works fine currently for inbound and outbound. Everything is registered, its perfect. My problems currently are: 1) After 20 minutes audio out to broadvoice goes away 2) After about 3 hours my registration attempts to broadvoice time out and the only solution is to switch to a different proxy which subsequently works.

Is the Broadvoice service up? I just signed up with them and started receiving calls in no time but could not make calls. And after a few minutes I cannot even place calls. register => [number]:[password]@sip.broadvoice.com [broadvoice] type=peer fromuser=[number] host=proxy.lax.broadvoice.com fromdomain=sip.broadvoice.com context=from-broadvoice dtmfmode=inband any help would be

I have been going crazy with this also since Sat. Our server was working perfectly with BV but will now not place calls to BV. Incoming from BV works fine. I felt sad rebooting it today, it had been running for almost 200 days! Here is my error message from the console... Notice I am running today's CVS Connected to Asterisk CVS-03/08/05-14:32:39 currently running on com (pid = 1624)

Hello - I've been using Broadvoice with Asterisk for a couple of months with no issues. Today, it has stopped registering. The Sip Debug from CLI is below. It tries to register five times and then gives up. Any suggestions? As you might suspect, I have not been able to get Broadvoice on the phone and usually get cut off after being on hold about 5 minutes. Strategic portions of IP

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

I cannot email them, I cannot call them, I do not get an answer, but the credit card is still charged, although NO phone calls are possible anymore, ... Are they still in business? (except charging credit cards)???? bye Ronald

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

Dear all, I have tried a lot of things to make broadvoice work with asterisk , but I failed each time. Please suggest a good service providers that I can use with asterisk for outbound and inbound calls. -- With regards, Vicky Shrestha System Director WorldLink Communications Jawalakhel , Kathmandu, Nepal

I had my asterisk configuration working very well with broadvoice, but it stopped working this afternoon. I plugged the Cisco 7960 phone I used for my origional signup (just a few days before they offered generic BYOD) and it works fine. I did notice it seems to do all of its comunication through proxy.broadvoice.com (I used tcpdump). I have never contacted broadvoice about using asterisk

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

Today, We have added INVITE Authentication. This seems to bring a large amount of problems to people in the way since they can't make outbound calls. Here's what needs to be done. You need to add three variables to your peers or friends, username, authuser, and secret. username=<phonenumber> authuser=<phonenumber> secret=<registration password> Dan

We have worked out all of the settings needed to get BroadVoice working. We have just completed testing on two seperate systems to make sure it is working. I am writing up details instructions right now and will have something available shortly. I just wanted BV users to know that a solution is on its way. Kerry Garrison http://www.geekgazette.com -------------- next part -------------- An

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

Hi All First time poster, long time reader. I just ran into something really bizarre. I've enabled videosupport and have been testing sip calls with Xten Eyebeam software, it works (mostly) However, when I have Videosupport=yes In the [general] section of my sip.conf, broadvoice calls fail w/ "We're sorry your call cannot be completed at this time" So... I've

I've been having a lot of problems with Broadvoice lately. Anyone else been without service for extended periods of time this week?